Access Official Technical PDF

Share Summary:LinkedInEmail

Selecting a 100 V power MOSFET for a converter, motor drive or solar application involves more than checking its drain-current rating. Engineers also need to consider gate-drive voltage, conduction loss, switching behavior, body-diode recovery and the thermal path from the device into the circuit board. The onsemi FDMS86181 is an N-channel MOSFET designed to address these requirements using shielded-gate POWERTRENCH technology. Its datasheet provides the conditions and limits needed to evaluate the device in a real power stage.

FDMS86181 at a glance

The FDMS86181 is rated for a 100 V drain-to-source voltage and is supplied in a Power 56 (PQFN8) package. The datasheet lists a maximum continuous drain current of 124 A with the case at 25°C, 78 A with the case at 100°C, and 17 A with ambient at 25°C under the stated conditions. These figures are not interchangeable: the actual current capability depends on the thermal and electrical design of the application, including the PCB.

The device is specified for a gate-to-source voltage of up to ±20 V. Its maximum static drain-to-source on-resistance is 4.2 mΩ at a 10 V gate drive and 44 A drain current. At a 6 V gate drive and 22 A, the maximum listed resistance is 12 mΩ. This difference makes gate-drive voltage an important part of device selection and loss analysis.

What shielded-gate technology means for power design

The datasheet describes the device’s shielded-gate process as optimized to reduce on-state resistance while maintaining switching performance. In practical terms, MOSFET selection involves balancing conduction losses against switching behavior. Lower on-resistance can reduce the resistive losses that occur while the device is conducting, while switching characteristics matter as the device transitions between on and off states.

The datasheet also identifies reduced switching noise and electromagnetic interference (EMI) as features, and describes the body diode as having soft recovery characteristics. It lists a 50% lower reverse-recovery charge (Qrr) compared with other MOSFET suppliers as a product feature; because that comparison is not accompanied here by a specific test setup or comparison device, designers should consult the manufacturer for the basis of the claim when benchmarking alternatives.

Interpreting resistance and switching data

On-resistance depends on operating conditions. At 10 V gate drive, the datasheet gives a typical value of 3.3 mΩ and a maximum of 4.2 mΩ at 44 A and 25°C. At a junction temperature of 125°C under the same gate-drive and current conditions, the listed typical and maximum values rise to 5.7 mΩ and 7.8 mΩ. This temperature dependence matters when estimating conduction loss across the operating range rather than at room temperature alone.

Switching figures are similarly tied to their test conditions. With a 50 V supply, 44 A drain current, 10 V gate drive and 6 Ω gate-drive resistance, the datasheet lists typical turn-on delay of 17 ns, rise time of 9 ns, turn-off delay of 25 ns and fall time of 6 ns. These values are useful for initial comparisons, but they do not by themselves predict switching performance in a particular circuit. The surrounding layout, driver and operating point must also be considered.

Total gate charge is specified as 42 nC typical and 59 nC maximum for a 0-to-10 V gate transition, measured at 50 V and 44 A. For a 0-to-6 V transition under the stated test conditions, it is 27 nC typical and 38 nC maximum. Gate charge helps engineers assess driver demand and switching design, but the final choice of drive conditions should be checked against the complete application requirements.

Body-diode behavior and application fit

The FDMS86181 is listed for primary DC-DC switching, synchronous rectification in DC-DC and AC-DC converters, motor drives and solar applications. In circuits where current commutates through the MOSFET body diode, forward voltage and reverse recovery are relevant design considerations. The datasheet gives a source-to-drain diode forward voltage of up to 1.2 V at 2.1 A and up to 1.3 V at 44 A, with gate-to-source voltage at 0 V under the stated pulse-test conditions.

Reverse-recovery values depend on the test conditions. At a forward current of 20 A and a current-change rate of 300 A/µs, typical recovery time is 32 ns and typical Qrr is 57 nC. At 1000 A/µs, the listed typical values are 25 ns and 158 nC. The change illustrates why diode data should be compared using equivalent test conditions and why system-level validation is necessary.

Thermal limits and board-level implementation

The datasheet lists a junction-to-case thermal resistance of 1.0°C/W. Junction-to-ambient thermal resistance is stated as 50°C/W when mounted on a 1 in², 2 oz copper pad, and 125°C/W for a minimum 2 oz copper pad. These figures show that board copper and mounting conditions affect the available thermal path. The specified 124 A continuous-current rating at a 25°C case temperature is therefore not a stand-alone design target: the datasheet notes that actual continuous current is limited by thermal and electromechanical application-board design.

The maximum junction and storage temperature range is −55°C to +150°C. The stated power dissipation is 125 W with the case at 25°C, compared with 2.5 W at ambient at 25°C under the datasheet’s conditions. When assessing a design, engineers should relate expected losses to the mounting arrangement, operating temperature and transient behavior, rather than relying on a single headline rating.

Making an informed selection

The FDMS86181 combines a 100 V rating, low specified on-resistance at a 10 V drive, switching data, and a PQFN8 package for applications including power conversion, motor drives and solar systems. Its suitability depends on whether the circuit’s voltage, current, gate-drive, thermal and commutation requirements align with the datasheet conditions.

For design reviews, compare resistance and switching figures at the intended operating point, check body-diode recovery against the circuit’s commutation conditions, and confirm that the PCB can provide the required thermal path. Finally, validate performance in the actual application: the datasheet cautions that typical parameters can vary and that operating parameters must be validated by the customer’s technical experts.

Access Official Technical PDF

About The Author