Access Official Technical PDF

Share Summary:LinkedInEmail

Finding an anode material that supports both rapid ion movement and substantial energy storage remains a challenge for lithium-ion and sodium-ion batteries. First-principles calculations point to a possible candidate: a hydrogen-passivated, two-dimensional gallium nitride (2D GaN) monolayer. The modeled material combines low calculated ion diffusion barriers with high theoretical capacities, making it worth examining as a potential 2D GaN anode.

Why combine diffusion and capacity?

Anode performance depends on more than how many ions a material can accommodate. Ion diffusion affects how readily ions can move across an electrode during charging and discharging, while storage capacity indicates how much charge the material can theoretically hold. Some proposed two-dimensional electrode materials perform well on one measure but less well on the other: materials with rapid diffusion may have moderate capacities, while high-capacity candidates can have larger diffusion barriers.

Two-dimensional materials attract interest partly because their exposed surfaces can provide sites for ion adsorption and pathways for movement. The study assessed whether a GaN monolayer could bring these advantages together for both lithium-ion batteries (LIBs) and sodium-ion batteries (NIBs). Its results are computational predictions, not evidence of battery-cell performance.

What the 2D GaN model looks like

Bulk gallium nitride has a non-layered wurtzite structure, so producing an isolated monolayer by simply exfoliating the bulk is not straightforward. Prior experimental work had reported large-area 2D GaN made using graphene encapsulation. The modeled monolayer is buckled, with its surfaces passivated by hydrogen atoms; calculations in the study also found the hydrogen-passivated structure energetically more favorable than the unpassivated form.

This structural detail matters when interpreting the battery results: the proposed electrode is not an unmodified slice of bulk GaN. The calculations examine ion adsorption and movement on a specific, hydrogen-passivated monolayer configuration.

Adsorption and electronic behavior

Among the adsorption positions examined, the energetically preferred sites were on the top surface of the GaN monolayer. The calculated adsorption energies at the most favorable site were −0.46 eV per lithium atom and −0.25 eV per sodium atom. The analysis also indicated substantial electron transfer from the adsorbed ions to the GaN sheet, consistent with chemical adsorption in the model.

The pristine GaN monolayer was calculated to be semiconducting. With lithium or sodium adsorbed, the modeled system became metallic. This predicted change is relevant because electronic behavior is one factor in assessing an electrode material, although the calculation alone does not establish conductivity or performance in a manufactured electrode.

Low calculated ion diffusion barriers

To evaluate ion mobility, the researchers compared three migration paths between neighboring favorable adsorption sites. The lowest calculated barriers were 79 meV for lithium and 22 meV for sodium. In the study’s comparisons with other modeled 2D anodes, these values were low, particularly for sodium.

The calculations further indicated that barriers could decrease as adatom coverage increased. At one-layer coverage, the reported barriers fell to 43 meV for lithium and 16 meV for sodium; at two-layer coverage, they were 37 meV and 11 meV, respectively. These are theoretical migration barriers for the modeled structures, not direct measurements of charging rate or battery power.

Theoretical storage capacity and voltage

The predicted maximum capacities were 938.1 mAh/g for lithium and 625.4 mAh/g for sodium. In the model, these capacities corresponded to the compositions Li3GaNH2 and Na2GaNH2, respectively. The calculations estimated average open-circuit voltage values across adsorption stages of approximately 0.06–0.26 V for lithium and 0.05–0.16 V for sodium, ranges considered compatible with anode operation in the study.

Stability was also examined computationally. Ab initio molecular dynamics simulations at 323 K found that the modeled, fully loaded lithium and sodium structures retained their configurations over the simulated period of 3 ps. This offers a limited indication of stability under those simulation conditions; it does not substitute for longer-term testing or experimental validation.

How the results compare—and what remains unknown

In comparisons with selected 2D anode materials, GaN’s calculated lithium capacity was among the highest, though some borophene structures had higher reported values. Those borophene examples also had substantially larger lithium diffusion barriers. For sodium, the study found that GaN paired a low calculated barrier with a capacity higher than several materials with similar barriers.

For engineers and battery developers, the key takeaway is the combination of predicted properties rather than a single headline number. The results identify a candidate for further investigation, but they do not establish practical manufacturability, cycle life, electrode-level capacity, or performance in a complete cell. Those questions require evidence beyond the first-principles calculations presented.

Conclusion

First-principles modeling suggests that a hydrogen-passivated 2D GaN monolayer could support both fast lithium and sodium diffusion and substantial theoretical storage capacity. Its calculated diffusion barriers—79 meV for lithium and 22 meV for sodium—alongside capacities of 938 and 625 mAh/g, respectively, make it a promising subject for continued materials research. The practical implication is clear: 2D GaN merits further study, while experimental validation must determine whether its modeled advantages can translate into a viable battery anode.

Access Official Technical PDF

About The Author