As transistor dimensions shrink, maintaining low leakage and reliable control of channel current becomes increasingly difficult. 2D materials electronics offers one possible route for exploring devices at these scales: atomically thin semiconductors can provide a very thin channel, while their band structure and layer-dependent properties create opportunities for different device designs. Quantum-transport modeling of transition metal dichalcogenides (TMDs) examines both the potential and the trade-offs.
Why consider atomically thin channels?
In a conventional field-effect transistor (FET), the gate must control the channel barrier strongly enough to switch current between on and off states. When the channel is shortened, the source and drain can also influence that barrier. This weakens gate control and contributes to short-channel effects such as drain-induced barrier lowering (DIBL) and increased off-state current.
A very thin body can improve the geometry available for electrostatic control. TMDs—including molybdenum disulfide (MoS2), molybdenum diselenide (MoSe2), tungsten disulfide (WS2), and tungsten diselenide (WSe2)—are layered semiconductors that can be studied as single-layer or few-layer transistor channels. Their electronic properties vary with both material choice and the number of layers, so thickness is a device-design variable rather than simply a manufacturing detail.
The motivation is not limited to transistor density. Off-state leakage contributes to circuit power, while supply voltage cannot be reduced indefinitely without affecting switching behavior. In a conventional MOSFET, the thermal switching mechanism imposes a fundamental subthreshold-swing limit of about 60 mV per decade at room temperature. Improving channel electrostatics may help manage scaling challenges, but it does not by itself remove that thermal limit.
What quantum-transport modeling reveals about TMD transistors
At nanometer dimensions, semiclassical device models can become inadequate because quantum effects influence carrier transport. The modeled approach couples the non-equilibrium Green’s function (NEGF) formalism with Poisson’s equation. NEGF calculates charge and current under specified device conditions; Poisson’s equation calculates the electrostatic potential from that charge and the device’s geometry and dielectric properties. Repeating the calculations establishes electrostatic self-consistency.
Using this framework, simulated TMD FETs with a 5 nm gate length show that material properties can support strong switching in an idealized, ultimately scaled configuration. The work reports an on/off current ratio of 105 for MoS2-based devices at that gate length. The result points to a possible low-power application, but it is a modeled intrinsic-performance result—not a claim that a manufactured device will achieve the same behavior.
Band gap and effective mass help shape the outcome. A sufficiently large band gap can help limit unwanted off-state conduction, while effective mass affects the electronic density of states and transport. The simulations compare four TMDs and find that transistor behavior changes with material and layer count. In particular, adding layers tends to weaken gate control, degrading subthreshold behavior and DIBL. The modeled degradation is especially pronounced for WSe2, while MoS2 shows comparatively better scalability in the studied configurations.
Layer count, screening, and gate architecture
Few-layer channels introduce an electrostatic challenge: charge in one part of the body can screen the gate field from other layers. In the MoS2 simulations, layer-resolved charge and current are not uniform. Which layer carries more current depends on the device configuration and operating state, as well as how strongly the gate controls each layer.
Comparisons of single-gate and double-gate structures show the value of controlling the channel from more than one side. The modeled double-gate devices have stronger electrostatic control than their single-gate counterparts. For bilayer and three-layer channels, however, screening still affects how charge is distributed through the body. A thicker channel therefore does not simply provide a straightforward increase in useful drive current: added layers can make it harder for the gate to control the full channel and suppress off-state conduction.
These findings make gate architecture and body thickness important considerations for device evaluation. They also underline why reporting a transistor’s material alone is not enough to characterize its expected behavior. Layer count, gate arrangement, and electrostatic conditions all matter.
Contacts remain part of the scaling problem
Channel performance is only one part of a transistor’s practical behavior. Electrical contacts influence how readily carriers enter and leave the semiconductor, and their resistance can limit the current available to a circuit. The dissertation’s analysis estimates intrinsic contact-resistivity limits for several TMDs and examines how those limits depend on carrier density and band structure.
The calculations show that contact behavior varies across materials and with the position of the Fermi level. Secondary conduction-band minima also affect the number of available transmission modes as energy changes. This helps explain why contact performance cannot be assessed from the channel’s band gap alone. The estimates describe intrinsic limits; they do not remove the need to address the materials and interfaces involved in practical contacts.
A possible route to one-dimensional spin channels
TMD heterostructures also offer a different device possibility. At a lateral junction between two materials, a conduction-band offset can create an in-plane electric field. In the modeled MoS2/WSe2 junction, spin-orbit coupling works together with this field under non-equilibrium conditions to produce a localized, one-dimensional spin channel, without an external magnetic field.
The calculated spin polarization at that junction is 0.1%. The analysis also considers how effective mass and spin diffusion affect the result: greater spin diffusion can spread polarization away from the junction and weaken the channel’s one-dimensional character. This is a proposed opportunity for studying confined spin dynamics and exploring spintronic devices, rather than a demonstrated industrial component.
Practical implications for device development
For engineers and technical decision-makers, the central lesson is that 2D materials should be assessed as part of a complete device architecture. Promising intrinsic switching results need to be considered alongside layer-dependent screening, contact resistance, gate configuration, and the distinction between simulation and fabricated-device performance.
NEGF-based modeling can help compare materials and structures where quantum effects matter, narrowing the questions that experimental development needs to address. TMDs such as MoS2 provide a useful case study: their thin channels and band properties may support scaled, low-power transistor concepts, while heterostructures suggest additional spin-based functions. Progress depends on balancing those opportunities against the electrostatic and contact limitations identified in the models.