A 3-bit digital RF phase shifter can steer or align radio-frequency signals by applying discrete changes to their phase. In a switched-line design, the signal is routed through transmission paths with different electrical lengths. A simulated design operating at 10 GHz illustrates this approach using coplanar waveguide (CPW) on an FR-4 substrate, with target phase shifts of 45°, 90° and 180°. For engineers assessing RF front ends, phased-array antennas or wireless communication hardware, the results show both the potential and the trade-offs of this transmission-line technique.
How a switched-line phase shifter works
Phase describes the position of a point in a repeating signal cycle. Changing the signal’s travel time changes that position relative to a reference signal. Because the electrical length of a transmission line depends on its physical length and the signal’s wavelength, selecting paths of different lengths produces different phase shifts.
A switched-line phase shifter uses switches to route the input signal through one of several transmission paths. This differs from a loaded-line arrangement, which changes the impedance applied to a line. The switched approach is conceptually straightforward to implement on a printed circuit board, although the switching elements and their layout remain important parts of a complete design.
Digital phase shifters provide discrete phase states rather than the continuously variable control associated with analog phase shifters. In RF and microwave systems, phase adjustment can support signal alignment and beam control in phased arrays, as well as other communication and measurement functions. The source design discusses a three-bit configuration but reports three target phase shifts—45°, 90° and 180°—so these are the states addressed in the reported simulation results.
Why use coplanar waveguide?
CPW places a center conductor and ground conductors on the same surface of a dielectric substrate. This planar arrangement is useful in RF circuit layouts, where transmission lines connect components on printed circuit boards or within integrated circuits. Unlike a structure that requires ground connections through the substrate, CPW can make it simpler to connect series or shunt circuit elements and create short-circuit terminations.
The reported design uses a 100 µm-wide center conductor with 14 µm gaps on 1.6 mm-thick FR-4. The substrate’s stated dielectric constant is 4.4, and the copper conductor thickness is 17 µm. The CPW is designed for a characteristic impedance of 50 Ω. These dimensions define the transmission-line structure used to realize the different electrical path lengths.
Estimating guided wavelength is a key step in setting those lengths. The design relates guided wavelength to free-space wavelength and the effective dielectric constant. Since a wave travels more slowly in the substrate environment than in free space, the guided wavelength is shorter. The required phase shift can then be associated with a portion of that guided wavelength, helping determine the line length for each state.
Simulated performance at 10 GHz
The design was simulated in Advanced Design System (ADS). At 10 GHz, the reported results for the three phase-shifter paths are:
- 45° target: 45.55° phase shift, −21.864 dB return loss and −0.080 dB transmission magnitude.
- 90° target: 84.76° phase shift, −18.411 dB return loss and −0.167 dB transmission magnitude. The reported phase error is 5.24°.
- 180° target: 177.10° phase shift, −36.560 dB return loss and −0.222 dB transmission magnitude. The reported phase error is 2.89°.
In the simulation, return loss is presented as S11 and transmission as S12. The negative transmission values, expressed in decibels, correspond to insertion loss; values closer to 0 dB indicate less signal attenuation. Among the reported paths, the 45° case has the smallest insertion loss, while the 180° case has the lowest return-loss value in the listed results. The achieved phase shifts are close to their targets, with the 90° state showing the largest reported phase error.
These figures are simulation results at the stated operating frequency, not a guarantee of performance in a manufactured assembly. The paper identifies reducing insertion loss and increasing isolation as areas for future work. In practice, the reported values should therefore be treated as design-specific results to evaluate, rather than universal performance expectations for switched-line phase shifters.
Design implications for RF system teams
For system integrators and hardware designers, the example underscores the connection between phase accuracy and transmission-line geometry. Small changes in the effective electrical length affect the resulting phase, while substrate properties and conductor layout form part of the design context. Choosing a phase state is not just a matter of specifying an angle; it involves balancing phase error, signal loss and input matching.
Evaluation should also account for the intended operating conditions. The reported design is centered on 10 GHz, and its simulation data should not be read as proof of performance across a wider frequency range. Teams should verify behavior across the frequencies and operating conditions relevant to their application, and assess the switching implementation as well as the transmission paths before relying on the design in an RF chain.
Conclusion
A switched-line 3-bit digital RF phase shifter offers a clear way to create discrete phase states by routing signals through CPW paths of different lengths. The simulated 10 GHz design achieves phase shifts close to its 45°, 90° and 180° targets, with reported insertion loss ranging from 0.080 to 0.222 dB in magnitude. For engineers considering this approach, the practical lesson is to assess phase accuracy, return loss and insertion loss together—and to validate simulated performance against the requirements of the complete RF system.