A 77-GHz automotive radar module must bring together far more than a radio-frequency front end. It also needs stable, low-noise power, onboard processing, an antenna, and a way to deliver useful detection data to the vehicle’s electronic control unit (ECU). A reference design built around a single-chip radar sensor demonstrates how these functions can be integrated on a compact board, while showing why power integrity, electromagnetic interference (EMI), and PCB layout matter to system performance.
The design covers the 76- to 81-GHz band and combines radar processing with a CAN-FD physical-layer transceiver. Its approximate 50 × 71 mm board requires two system connections: battery power and CAN-FD output. This architecture is relevant to applications such as blind-spot detection, lane-change assistance, cross-traffic alert, adaptive cruise control, and automatic emergency braking.
How a 77-GHz automotive radar module processes object data
The radar device integrates radio-frequency (RF) and analog circuitry with digital processing. Its four receive channels and two transmit channels work with a printed-circuit-board antenna array. The sensor transmits a frequency-modulated continuous-wave (FMCW) chirp and samples the returning reflections. Onboard processing uses those signals to determine object distance, angle, and velocity.
Instead of sending raw radar signals to a separate processor, the module outputs processed object data over CAN-FD to a central ECU. The reference design supports a CAN-FD data rate of up to 5 Mb/s. This provides a defined interface between the sensor and the wider vehicle system, while keeping radar acquisition and processing on the module.
Integration can simplify the sensor’s external connections, but it places several demanding functions close together. The RF circuitry is sensitive to supply noise, and the switching regulators and their current paths can create interference if power distribution and PCB layout are not carefully managed.
Power architecture: wide input and multiple rails
The module is designed to connect to an automotive battery input. A wide-input buck converter generates a 3.3-V intermediate rail, and a multi-rail power device derives supplies for the radar and CAN-FD circuitry. The design uses 5 V for the CAN-FD PHY, 3.3 V for radar I/O, 1.8 V for radar analog and related circuitry, and approximately 1.2 V for digital logic and SRAM. A separate low-noise regulator provides a 1-V supply for the RF section.
This approach reflects a common challenge in radar power supply design: each domain has different requirements. Digital rails must support their loads, while analog and RF rails need careful filtering to prevent switching noise from degrading the received signal. The design raises a nominal 1.2-V rail to 1.24 V to provide sufficient headroom for the regulator producing the 1-V RF supply. Supplying the regulator from this lower rail, rather than 1.8 V, also reduces the voltage it must drop.
The reference design specifies a 4- to 42-V input range, with 12 V as the typical supply, and reports 2.6 W typical total consumption at 12 V. These figures describe the design’s stated operating conditions; actual radar current depends on the selected chirp profile and frame configuration.
Protecting RF performance from supply noise
Switching converters are efficient, but their ripple and switching currents can couple into sensitive radar circuitry through power or ground paths. The design uses several complementary measures to limit this risk:
- Filter sensitive rails: LC filtering on the analog and RF supplies reduces ripple reaching the radar device.
- Manage switching ripple: A high switching frequency and suitable output capacitance help control regulator ripple and load-step response.
- Use point-of-load decoupling: Local capacitors help suppress supply disturbances near the loads.
- Control return-current paths: PCB routing that keeps switching currents localized can reduce unwanted voltage gradients in shared ground planes.
The design also uses a low-noise LDO for the RF rail. Its purpose is to attenuate upstream switching noise while supplying a noise-sensitive load. The power-management device includes monitoring and watchdog functions, supporting diagnostic and supervision needs in automotive applications. These features do not remove the need for system-level safety analysis and validation.
Automotive power transients and EMI
Battery-powered electronics must operate across changing input conditions. Cold crank can cause a substantial voltage drop, while load dump can expose the supply to a high transient. A wide-input buck stage is intended to handle this challenging input environment and maintain regulation for downstream rails within its operating limits.
EMI control also depends on more than adding filters. Converter package construction, input-capacitor placement, and the geometry of high-current loops all influence noise. The reference design emphasizes minimizing parasitic inductance around the switch node and arranging input capacitors to reduce the area of noisy current loops. A converter option with spread-spectrum switching can distribute harmonic energy across a wider frequency range, reducing peak noise levels; it does not eliminate the underlying noise floor.
Antenna and PCB choices at millimeter-wave frequencies
The module’s etched antenna array provides two transmit elements and four receive elements for detecting and tracking objects. The reference design reports peak antenna gain above 9 dBi across 76 to 81 GHz. At these frequencies, PCB material and fabrication tolerances are important: the antenna is implemented using a low-loss laminate rather than standard FR4, which the design identifies as unsuitable for the required antenna performance. Small variations in etched features matter because the operating wavelength is only a few millimeters.
PCB layout must address RF routing as well as power-converter currents. Designers need to consider where switching return currents flow, how sensitive radar supplies are filtered, and how ground-plane structure affects coupling. CAN bus termination is another system-level detail: the cable should be terminated to match its characteristic impedance, with two terminations maintained at the ends of the bus. Split termination is an option when common-mode filtering and emissions behavior need attention.
Practical implications for system designers
This reference design illustrates the system-level decisions behind a compact automotive radar sensor: integrate processing and CAN-FD output, generate several carefully managed supply rails from the battery, isolate sensitive RF power from switching noise, and select PCB materials and layouts suited to millimeter-wave operation. For engineers evaluating a similar architecture, the practical lesson is to treat power integrity, EMI, antenna implementation, and vehicle-network connectivity as interdependent design tasks—not as separate finishing steps. The reference design provides a starting point, but each application still requires independent validation against its electrical, environmental, safety, and regulatory requirements.