In semiconductor manufacturing, process conditions inside a growth chamber must be understood before valuable production wafers are processed. A sensor wafer can be placed in the chamber at the same position planned for a production wafer, collecting temperature and pressure data to help engineers calibrate deposition conditions. Powering these devices is a specialized challenge: sensor wafer batteries must be thin enough to fit the wafer assembly and operate in a hot, low-pressure environment where conventional options may not be suitable.
Why sensor wafers are used in semiconductor processing
Silicon wafers are the starting material for many semiconductor chips used in products such as smartphones, wearables, autonomous vehicles and consumer electronics. Before a wafer becomes a finished chip, it passes through processing steps that can include deposition, photolithography, etching, laser patterning and dicing. The conditions during deposition are important to the process, so engineers need a way to assess what is happening inside the chamber.
A sensor wafer provides a practical means of gathering that information. It is introduced into the growth chamber shortly before the production wafer, in the location where the production wafer will be placed. It measures conditions such as temperature and pressure. Depending on the system, the resulting data can be transmitted wirelessly to engineers or stored on a memory chip on the wafer and retrieved after removal.
This measurement step supports calibration of chamber conditions before the production deposition takes place. It also places the sensing hardware in an environment that presents demanding requirements for its power source.
Power requirements for sensor wafer batteries
A battery for a sensor wafer has to satisfy several constraints at once. A growth chamber is hermetic, making a cabled power connection impractical. The battery must therefore provide power within the wafer assembly rather than relying on a cable routed into the chamber.
Temperature is another critical factor. The chamber can reach 150°C or higher, so a power source must be able to operate at elevated temperatures. At the same time, sensor wafers are only a few millimetres thick, which leaves little room for a battery. The battery itself typically needs to be around 1 mm thick or less.
The chamber’s low-pressure environment adds a further consideration. Batteries containing liquid solvents are not suitable for this application, according to the application note. Taken together, the constraints call for a compact power source that can function at high temperature and low pressure without taking up space needed by the sensor wafer design.
How solid-state batteries address chamber constraints
Solid-state batteries replace the flammable solvent found in conventional lithium-ion batteries with a solid electrolyte. The application note identifies the solid electrolyte’s greater resistance to higher temperatures as an important reason this battery type is relevant to sensor wafer applications.
Ilika’s Stereax P180 is described as a solid-state battery intended for this use. Its stated operating temperature range is -40°C to +150°C, and its thickness is less than 1 mm. Those characteristics align with two central design requirements: fitting into a thin wafer assembly and operating at temperatures found in a growth chamber. The application note also states that work was underway to increase the batteries’ maximum operating temperature; this is a development aim, not a specification beyond the stated range.
The P180’s other listed characteristics include capacity from 180 to 250 μAh and the ability to store energy harvested from the environment. The application note describes the battery as leakage-free and safe, and as resistant to high-moisture and high-vibration environments. It also lists a life of up to 10 years with thousands of cycles, and notes that the design is customisable and scalable. These are product characteristics presented for the battery; system designers still need to assess whether they meet the demands of a particular sensor wafer and process.
Design considerations for engineers and integrators
When evaluating a battery for chamber instrumentation, engineers and system integrators can use the application constraints to guide their review:
- Temperature: Check the required chamber operating range against the battery’s stated limits, including any periods of elevated temperature.
- Available space: Confirm that the battery’s thickness and overall form factor fit the wafer assembly.
- Pressure and materials: Consider the low-pressure chamber environment and whether the battery chemistry is appropriate for it.
- Data handling: Decide whether sensor readings will be transmitted wirelessly or stored for download after the wafer is removed.
- Energy needs: Compare the sensor system’s power requirements with the battery’s listed capacity and any available energy-harvesting arrangement.
These considerations connect battery selection to the complete measurement system. The power source, sensing electronics, data storage or communication method, and wafer geometry all need to work together within the chamber’s operating conditions.
Practical implications for semiconductor process monitoring
Sensor wafers allow engineers to measure chamber conditions at the location where production wafers will be processed, supporting calibration of deposition parameters. Their usefulness depends in part on fitting a reliable power source into a very limited space without compromising operation in heat and low pressure.
Solid-state batteries such as the Stereax P180 are presented as one option for addressing these requirements through a sub-millimetre profile, a stated temperature range up to +150°C, and a solid electrolyte. For plant and process teams, the practical next step is to match those specifications to the chamber profile, sensor load and data strategy of the intended application. Careful system-level evaluation helps determine whether a given battery is suitable for the measurement task.