Industrial waste heat recovery can be constrained by more than the temperature of an exhaust stream. Heat may be available at the wrong time or in the wrong place, while transport and equipment costs make reuse difficult. A thermal storage system using HAS-Clay addresses this mismatch by capturing low-temperature heat for later use or transport. Its development also offers a useful view of how materials engineering, system design, industrial manufacturing and demonstration work together to move technology toward practical application.
Why low-temperature waste heat is difficult to use
Factories and other facilities release heat that could potentially serve another process, but recovery is not always straightforward. The source material identifies low-temperature waste heat around 100°C as particularly challenging to use effectively. Even when a suitable heat source exists, the demand may be separated from it by time or distance. That creates a need to store heat and, in some cases, move it to another site.
The HAS-Clay project brought together five companies and a research institute, with Takasago Thermal Engineering leading system development and the National Institute of Advanced Industrial Science and Technology (AIST) leading materials work. The project focused on developing a heat storage material and a system for recovering and using heat outside the point where it was generated.
How HAS-Clay thermal storage works
HAS-Clay uses desiccant thermal storage, which stores heat through moisture adsorption and desorption. During charging, waste heat dries the material. The dried material can then be held in a thermal storage tank and transported. At the destination, moisture is introduced and adsorbed by the material, releasing heat for use.
This approach differs from sensible heat storage, which relies on raising a material’s temperature, and latent heat storage, which uses a phase change. The source describes desiccant storage as suitable for extended storage without temperature control and highlights HAS-Clay’s potential for transport. In practical terms, the system is designed to separate the time and location of heat capture from the time and location of heat use.
From material performance to an industrial system
One development challenge was improving the material’s suitability for production and deployment. Conventional powdered HAS-Clay had limitations involving bulk density and production cost. The team refined its composition and granulation conditions to produce a granular form. According to the project account, the resulting material achieved more than twice the heat storage density of conventional products and heat storage efficiency above 90%. Changes to particle size and shape also supported a design intended to limit energy loss.
Moving from laboratory development to industrial-scale production required a separate set of capabilities. Ishihara Sangyo contributed manufacturing expertise to address mixing and stirring challenges and establish mass production of the material. At its Yokkaichi Plant, the company also demonstrated stationary equipment that reused waste heat in a drying process. The work helped establish a system design and operating method for using recovered heat at a facility.
For heat transported away from its source, the team considered both cost and safety. Granulation increased the amount of heat that could be transported using the same amount of HAS-Clay, helping reduce transport costs. Using less material for the same amount of stored heat also made it possible to reduce equipment size. In an offline transport demonstration with Hino Motors, dried HAS-Clay was moved by truck to a remote location. The project also incorporated nonflammable materials and overheat prevention functionality, and developed a method for evaluating offline heat transport systems.
Demonstration connects engineering to operating conditions
Demonstrations help reveal whether a technology can function as part of a real operating environment, rather than only as a material or laboratory concept. The project tested stationary heat storage and heat release, as well as transport to a remote location. These activities addressed different system requirements: integration with a process at the heat source, handling and logistics between sites, and delivery of useful heat at the destination.
The project account reports that the system was introduced commercially as Mega Stock in 2024. That progression—from material development through manufacturing, demonstrations and market introduction—illustrates why industrial technology development often depends on coordinated work across the value chain, not solely on a breakthrough in material science.
Related examples: hydrogen combustion and robotic handling
Other technology-development examples demonstrate how distinct engineering problems require similarly joined-up development. Kawasaki Heavy Industries developed a dry hydrogen gas turbine cogeneration system using micromix combustion. Small fuel injection holes create numerous microflames, a design intended to avoid localized high-temperature areas and support low-NOx combustion. The project also addressed combustion vibration through measurement and visualization, followed by repeated testing. Demonstrations in Kobe generated electricity and heat for nearby facilities, and the development included hydrogen-only and hydrogen-natural-gas co-combustion configurations.
In robotics, Double Giken’s D-Hand uses a mechanical linkage to coordinate multiple fingers from a single power source. The fingers adapt to an object’s shape, enabling the hand to grasp objects of different forms. Development work addressed motor control, resistance to external forces and repeatability of movement. These examples are not waste heat systems, but they underline a shared lesson: practical deployment depends on resolving system-level challenges alongside core technical performance.
Practical implications for industrial decision-makers
For plant managers, engineers and system integrators assessing energy recovery, the HAS-Clay case points to several questions worth addressing early:
- Match heat supply to demand: Identify whether the main obstacle is temperature, timing, distance or a combination of factors.
- Evaluate the complete system: Include storage equipment, material handling, transport and heat delivery—not only the storage medium.
- Plan for manufacturing scale: Production methods and material consistency can determine whether a promising laboratory result is deployable.
- Demonstrate in relevant conditions: Test process integration, operating methods and safety measures before wider implementation.
Industrial waste heat recovery becomes more practical when the engineering addresses the full path from heat source to heat user. HAS-Clay demonstrates one approach: store heat through moisture adsorption and desorption, then use it at the same or a remote site. The broader takeaway is that commercialization depends on combining material innovation with manufacturing, system integration, safety planning and demonstration—turning available energy into a resource that operations can use.