Access Official Technical PDF

Share Summary:LinkedInEmail

Terahertz (THz) spectroscopy can reveal information about materials and processes across a broad frequency range, but no single conventional emitter performs equally well from the low-frequency region through several terahertz. A hybrid spintronic terahertz emitter offers a way to address this gap: it combines emission from a magnetic metal stack with laser-triggered photoconduction in a semiconductor. In the demonstrated device, an applied bias current strengthens the lower-frequency signal while leaving higher-frequency performance comparable.

Why broaden the terahertz spectrum?

THz time-domain spectroscopy (TDS) relies on short electromagnetic pulses to measure a sample’s response over a range of frequencies. The breadth of that range matters because a wider spectrum can provide more information for applications such as chemical characterization and nondestructive testing.

Existing source technologies have different operating strengths. Photoconductive antennas are effective across roughly 0.1–4 THz, but their performance falls at higher frequencies. Electro-optic crystals and air-plasma sources can perform well at higher frequencies, while their output in the lower THz range may be weaker. Combining emission mechanisms is a potential solution, but integration can be complicated by phase mismatch: if the emitted waves are out of phase, they may interfere destructively.

How a spintronic terahertz emitter works

The spintronic component uses a heavy-metal/ferromagnet (HM/FM) bilayer. A femtosecond laser pulse excites the ferromagnetic layer and drives an ultrafast spin current into the heavy metal. There, the inverse spin Hall effect (ISHE) converts the spin current into a transverse charge current, which produces THz electromagnetic radiation.

Spintronic emitters are attractive as broadband sources, with reported emission extending to around 10 THz. However, their output can be limited in the 0.1–0.5 THz range. The hybrid approach pairs the metal stack with a semiconductor channel so a second emission mechanism can contribute where the spintronic source is weaker.

Adding current-assisted photoconduction

In the demonstrated configuration, a high-resistivity silicon substrate supports the metal layers. When the laser pulse has photon energy above the semiconductor’s bandgap, it creates electron-hole pairs in the silicon. The resulting reduction in resistance enables a transient photocurrent under an applied bias. This rapid photoconduction generates an additional THz signal.

The semiconductor and magnetic-stack signals are emitted nearly simultaneously. Because the metal films are only nanometers thick—small compared with a THz wavelength—the researchers describe negligible dispersion through the spintronic layers and no significant phase mismatch between the two contributions. Under the appropriate conditions, the signals combine constructively rather than canceling.

The proof-of-concept devices used high-resistivity silicon with either a 6 nm platinum or tungsten layer and a 3 nm cobalt layer. A pulsed bias current was applied through patterned wires, alongside an external magnetic field to saturate the cobalt magnetization. The current was synchronized with the laser excitation to limit current-induced heating.

What the measurements show

With bias current applied, the THz signal increased in the lower-frequency region. The reported enhancement in the 0.1–0.5 THz band was 2–3 orders of magnitude compared with typical ISHE-based emission without the bias-assisted contribution. At higher frequencies, the hybrid emitter maintained comparable performance; measurements reported similar output up to 8 THz under different current conditions.

Several controls helped distinguish the two emission mechanisms:

  • No laser excitation: Applying current without the laser pulse did not produce an observed THz signal.
  • No silicon substrate: Devices with the metal bilayer on glass showed no sizable current-dependent enhancement.
  • Reversing current: The semiconductor-related signal reversed with current direction, consistent with photoconduction switching.
  • Changing the heavy metal: Platinum- and tungsten-based devices showed opposite current polarities for the strongest combined output, consistent with the opposite signs of their spin Hall angles.

Measurements that varied the directions of the magnetic field and current further separated the contributions. The spintronic signal depended on the magnetic-field orientation, while the silicon photoconduction signal depended on the bias-current direction. When the measurement geometry aligned with neither contribution, no THz signal was observed in the measured polarization.

Implications for THz system design

The result is a single-chip hybrid emitter that extends spintronic THz output toward lower frequencies without a reported loss of comparable higher-frequency performance. For THz-TDS developers, it illustrates how combining emission mechanisms can address a spectral weakness without requiring two separate emitter technologies. The study establishes a proof of concept, not a universal design specification: the demonstrated response depends on the semiconductor, magnetic stack, current direction, and measurement geometry.

For engineers evaluating broadband THz sources, the practical lesson is to consider both the emitter’s frequency response and the interaction between its emission mechanisms. In this design, bias-assisted photoconduction fills part of the low-frequency gap, while ISHE-based emission provides the broadband spintronic component. Together, they offer a route to wider-spectrum THz emission for spectroscopy systems.

Access Official Technical PDF

About The Author