In DC-AC power conversion, current measurement must fit both the electrical range of the application and the demands of its control or monitoring system. Isolated current sensors are one option for measuring current while maintaining voltage isolation between the measured circuit and the sensor output. The available choices range from compact, high-frequency sensor ICs to closed-loop current transducers designed for higher currents and precision measurement.
Comparing current range alone is not enough. Accuracy, bandwidth, response time, isolation rating and supply voltage all affect whether a device is suitable for a particular measurement task. The specifications available for three sensor families illustrate how these factors vary across different measurement needs.
How to compare isolated current sensors
Start by defining the expected current range and whether the measurement must accommodate current in both directions. The devices discussed here specify bipolar ranges, shown with a plus-or-minus sign. Next, consider how quickly the signal must respond and what frequency content the measurement needs to capture. Bandwidth and response time are related considerations, but they describe different aspects of sensor behavior: bandwidth indicates the frequency range over which the sensor responds, while response time describes how quickly it reacts to a change.
Accuracy also needs to be read alongside the conditions given for each device. For example, one transducer specifies accuracy over a stated frequency range, while other figures are presented without that same qualification. Supply voltage and isolation are practical integration criteria: the sensor must be compatible with the surrounding electronics and the voltage-isolation requirement of the measurement design.
Current sensor ICs for high-frequency measurement
The AKM CQ sensor IC family is specified for current ranges from ±4.5 A to ±42 A, with accuracy below 1.3%. Its stated bandwidth is DC to 1 MHz at -3 dB, and its response time is 0.5 microseconds. These characteristics make the family relevant to designs where high-frequency response is an important selection criterion within the specified current range.
The CQ variants differ in supply voltage: CQ-33xx devices use 5 V, while CQ-32xx devices use 3.3 V. The stated voltage isolation is 3 kV. For engineers integrating a sensor into a converter or measurement circuit, these details help narrow the choice based on available supply rails, required isolation and measurement dynamics. The specified accuracy and current range should also be checked against the application’s operating requirements rather than treated as interchangeable with the other product families.
Closed-loop transducers for higher current ranges
The VAC closed-loop zero-flux current sensors cover a substantially higher current range, from ±200 A to ±1,000 A. Their specified accuracy is below 0.5%, and the listed bandwidth is DC to either 50 kHz or 100 kHz at -3 dB, depending on the model. Response time is less than one microsecond.
Supply options also depend on the model: the listed requirements are ±12 V to 15 V or +24 V. This makes model-level verification important during system design. A designer should match the specific transducer’s range and bandwidth to the intended measurement, then confirm that its supply requirements can be met by the control cabinet or test setup.
The VAC family’s published range and accuracy figures distinguish it from the lower-current ICs, while its bandwidth figures are lower than the IC family’s stated 1 MHz. That comparison is useful when prioritizing requirements, but it does not by itself determine suitability: the required current range, frequency response, supply and accuracy must be considered together.
High-stability measurement with a fluxgate transducer
The Danisense DS200LP is described as a high-stability, high-precision closed-loop fluxgate current transducer. Its current range is ±300 A peak, with a 200 A RMS rating. Accuracy is specified below 0.3% from DC to 5 kHz. Its bandwidth is DC to 200 kHz at -1 dB, response time is less than one microsecond, and supply voltage is ±15 V.
The accuracy specification is explicitly tied to the DC-to-5-kHz range. The bandwidth is given using a different criterion, -1 dB, rather than the -3 dB figure used for the other products. These figures should not be compared as though they were measured under identical conditions. When evaluating transducers, engineers should retain the stated frequency range and bandwidth convention alongside the headline number.
Selection checklist for system designers
A practical comparison should include the full set of relevant specifications, not just the advertised accuracy or maximum current. Before selecting a sensor, verify:
- Current range: Does the device cover the expected current, including the required positive and negative directions?
- Accuracy conditions: Is accuracy specified for the frequency range relevant to the measurement?
- Bandwidth: Does the stated bandwidth and its measurement convention match the signal characteristics the system must capture?
- Response time: Is the specified response appropriate for the intended measurement or control task?
- Isolation: Does the stated voltage isolation meet the design requirement?
- Power supply: Can the system provide the voltage required by the specific model?
Keeping these criteria together prevents a common comparison error: focusing on one attractive specification while overlooking a mismatch in current range, supply voltage or measurement conditions.
Conclusion: match the sensor to the measurement task
The three product families illustrate distinct combinations of range, accuracy, frequency response and integration requirements. The AKM CQ ICs offer a stated bandwidth up to 1 MHz across lower current ranges; VAC zero-flux transducers address ranges up to ±1,000 A with model-dependent bandwidth and supply options; and the DS200LP specifies high accuracy over DC to 5 kHz alongside bandwidth to 200 kHz at -1 dB.
For automation engineers, system integrators and power electronics designers, the practical choice depends on the measurement conditions—not a single headline figure. Comparing each device against the actual current range, accuracy needs, bandwidth, response time, isolation and available supply voltage provides a sound basis for selecting a current measurement component.