Access Official Technical PDF

Share Summary:LinkedInEmail

AC voltmeter maintenance begins with understanding what the instrument measures and how its reading is produced. The Hewlett-Packard 400E and 400EL are legacy AC voltmeters designed to measure voltage and decibels, and they can also serve as an AC-to-DC converter or a wideband AC amplifier. Their operating principles and service checks offer useful lessons in measurement practice: a meter’s scale, signal waveform, input limits, and calibration condition all affect how its readings should be interpreted.

What the HP 400E/400EL measures

The 400E/400EL covers full-scale voltage ranges from 1 mV to 300 V across 12 ranges, with a frequency range of 10 Hz to 10 MHz. The 400E emphasizes voltage readability, while the 400EL provides a linear decibel scale for easier dB readings. Both instruments display volts and decibels; the difference is the arrangement of the scales. An available option on the 400E places the dB scale at the top for improved readability, while Option 02 provides a relative-reference adjustment.

A key specification is that the meter is average responding but calibrated in RMS volts. It measures the average value of the applied AC signal and scales the indication to show an RMS-equivalent value. That relationship is appropriate for the expected waveform, but distortion can introduce error because a distorted signal does not necessarily have the same relationship between average and RMS values as the waveform assumed by the calibration. A reading should therefore be considered in light of signal quality, not just the meter range.

Operating the AC voltmeter safely

Before applying power, check that the rear-panel 115/230 V selector matches the supply. The instrument is specified for 115 or 230 V AC, within ±10%, at 48 to 440 Hz. A three-conductor power cable and a properly grounded outlet help ground the chassis. For battery operation, the manual calls for two batteries providing 35 to 55 V each and specifically requires connecting the chassis terminal to earth ground for operator protection.

Start with a range appropriate to the expected signal, then connect the source to the AC input. Avoid exceeding the instrument’s input limits. The manual specifies a maximum of 500 V RMS AC on the 3 V through 300 V ranges, a 300 V DC limit on any range, and range-dependent overload limits for the 1 mV through 1 V ranges. Exceeding these limits may damage the instrument. Internal adjustments and component replacement require qualified service personnel; disconnect power and discharge circuits before working inside, since hazardous voltages may remain under some conditions.

Interpreting decibel readings

To obtain a dB reading, add the scale indication algebraically to the selected range setting. The instrument’s dBm reference is 1 mW dissipated in a 600-ohm load. A reading made across another impedance can be expressed in dB, but it is not directly a dBm measurement under that reference condition. The manual provides an impedance-correction graph for converting readings taken across other loads.

Using the converter and amplifier outputs

The rear-panel DC output provides a 0-to-1 V signal proportional to meter deflection. Its output resistance is 1,000 ohms, so loading it with a low-impedance measuring device can affect the result. Use a high-input-impedance instrument when monitoring this output.

The AC output provides an amplified or attenuated version of the input, depending on the range. Its output impedance is 50 ohms. The specified output is 150 mV RMS at full-scale indication, except on the 1 mV range, where it is 105 mV. The manual also advises placing a 1-kilohm shielded load across the DC output when the AC output is in use and the DC output is otherwise unused, particularly on low ranges.

AC voltmeter maintenance and performance checks

Performance checks compare the instrument’s behavior with its specifications before calibration adjustments are attempted. The manual describes checks for accuracy and frequency response, input impedance, converter output impedance, and AC output voltage. It also calls for a mechanical zero adjustment on the 400E before performance checks or calibration.

Accuracy and frequency-response testing can use different test methods depending on the available equipment and required uncertainty. The documented approaches include an AC calibrator, a test oscillator, and a thermal-converter method. The calibrator method is described as the simplest and most accurate option for the stated voltage and frequency range. At higher frequencies, the manual describes using a test oscillator for specified ranges. Thermal converters require additional setup and careful handling; the test signal must have very low distortion because the converter and average-responding meter respond differently to waveform distortion.

For repeatable checks, allow the instrument and relevant test equipment to warm up as specified for the selected procedure, use suitable equipment, and record readings against the applicable range and frequency tolerances. If results fall outside those tolerances, proceed to the manual’s alignment and calibration procedure rather than making adjustments based on a single unexplained reading.

Practical implications

The 400E/400EL’s versatility comes with measurement conditions that matter: average response affects readings on distorted waveforms, dBm depends on a 600-ohm reference load, and the converter outputs must be used with appropriate loading. Safe operation also depends on grounding, correct line-voltage selection, and respecting range-specific limits. For technicians maintaining one of these instruments, a disciplined sequence—inspect, verify operating conditions, perform documented checks, then calibrate if necessary—helps keep measurements interpretable and service work controlled.

Access Official Technical PDF

About The Author