Access Official Technical PDF

Share Summary:LinkedInEmail

The LV8968BB evaluation board gives engineers a hardware platform for developing and assessing three-phase motor-control systems. Built around the LV8968BB gate driver, it combines a MOSFET inverter with microcontroller interfaces and optional circuitry for current measurement, back-EMF (BEMF) sensing and PWM control. Its configuration can support experiments ranging from basic sensorless commutation to more advanced control algorithms, while leaving the choice of microcontroller and control software to the user.

What the LV8968BB evaluation board includes

The board is designed for industrial and automotive application evaluation, with a recommended maximum power level of 250 W. Its operating supply range is 8 V to 25 V, with 12 V typical. The power stage uses six N-channel MOSFETs in a three-phase inverter arrangement. The listed MOSFET type is rated at 40 V and 85 A, with 5.7 mΩ typical on-resistance; the board documentation notes that the device may change and that users may select a different type to suit their application.

A microcontroller is not included. This lets development teams use their preferred controller and implement their own motor-control firmware. The board can connect to an Arduino Due, or users can connect an alternative microcontroller through a dual-row, 50-pin header. For a 12 V nominal motor of up to 200 W, the manual specifies a supply of 20 V or greater with an output current above 10 A. The supply must also be able to provide the current required by the intended motor.

Microcontroller connection and control signals

The Arduino shield interface is intended for an Arduino Due board, while the 50-pin header accommodates other microcontrollers. The alternative controller must provide at least three PWM generators, 15 digital I/O pins and six analog inputs, along with a compatible cable and connector. Digital input signals are compatible with 3.3 V and 5 V levels. The LV8968’s open-drain outputs may require its VCC level to be raised from the 3.3 V default to 5 V through SPI configuration.

In its default configuration, the LV8968 can respond to phase-control signals without first requiring SPI setup. Activating the inverter requires a high signal on EN together with the appropriate phase inputs. The low-side FET controls are active low, whereas the high-side controls are active high; pulling EN low disables the output stage. Default settings also disable errors and set dead time to 3.2 μs, the maximum setting. Engineers should review these defaults and configure the device as needed for their control strategy.

SPI provides access to device settings. Communication is full duplex: data is latched on the rising clock edge and should change on the falling edge, and CSB must return high after each transmission. The device datasheet should be consulted for register-level details.

Monitoring, PWM and sensing options

System signals help the microcontroller manage board state and respond to faults. The WAKE input brings the LV8968 out of sleep when driven high; the board includes a switch that connects WAKE to the supply. The DIAG output indicates system errors and warnings, while a low VMCRES signal indicates a watchdog violation. The watchdog is disabled initially and must be activated through SPI. In a finished application, VMCRES would typically be connected to the microcontroller’s master reset, but the evaluation setup does not make that connection because watchdog events could disrupt programming and debugging.

PWM can come from an external signal or from the board’s onboard generator. The external input is selected with jumper JP2. Alternatively, the onboard circuit supplies a 100 Hz PWM signal, and a potentiometer adjusts its duty cycle from 0% to 100%. The potentiometer’s analog output is also available to the microcontroller. Two pushbuttons provide additional inputs, such as for motor commands or demo-program selection, and require microcontroller inputs configured with pull-ups.

For motor feedback, the board supports low-side shunt measurement across three phase resistors. The LV8968BB has one programmable-gain current-sense amplifier for the center shunt, while two additional amplifiers on the board measure the other two phase currents. The manual also describes a single-shunt configuration, enabled by shorting solder jumpers RO2 and RO3. These options let engineers explore different current-sampling approaches, including measurements relevant to field-oriented control.

A star-point comparator supports simple BEMF algorithms. It compares the virtual motor star point with the LV8968’s AOUT signal; using this feature requires routing AOUT to the phase voltages through SPI configuration. The microcontroller can then monitor STARCOMP to determine motor phase transitions.

Power-up and high-side gate supply considerations

Apply the supply through connector J2 or the power jack J3. The corresponding indicators show when the input and 7.5 V regulator are active. Operating the WAKE switch powers up the LV8968 and enables its 3.3 V VCC supply. Because the board cannot perform useful motor control without controller commands, connect and configure the microcontroller before proceeding with motor operation.

The high-side gate supply can use one of three arrangements: the default bootstrap circuit, an undervoltage charge pump, or a modified charge-pump configuration for 100% output duty. The appropriate hardware and jumper configuration depend on the intended operating mode. For the undervoltage charge pump, the controller supplies a 50 kHz clock and should monitor supply voltage or respond to an undervoltage diagnostic. The 100% duty configuration requires component changes and careful control of the charge-pump clock; the documentation warns that incorrect operation can cause overvoltage damage.

Power handling also needs attention. The J3 input includes a reverse-polarity zener rated at 3.9 A maximum, while J2 uses a MOSFET-based reverse-polarity arrangement. With J2, motor braking or regeneration can return energy to the supply. The board documentation says supply ripple must be filtered adequately and that regenerative energy must be managed, for example through controlled braking. System designers should account for their supply and load behavior rather than assume the board absorbs returned energy.

Applying the board in development

The LV8968BB evaluation board brings together inverter switching, controller interfacing and optional sensing circuits in one development platform. Its practical value lies in making these functions configurable: teams can choose their microcontroller, set device parameters over SPI, select a PWM source and investigate different current- and BEMF-sensing methods.

Before applying the board to a motor-control design, verify the supply, motor, interface levels, gate-supply configuration and fault-monitoring logic against the intended operating conditions. The evaluation board is a development tool, not a finished product; designs based on it require application-specific testing and validation. Careful configuration and monitoring help engineers use the platform to assess control approaches while understanding the electrical and operational limits that shape a production implementation.

Access Official Technical PDF

About The Author