A GaN half-bridge evaluation can help engineers assess gate-driver behavior and switching performance before developing a power-conversion design. The LMG1210EVM-012 is an open-loop evaluation board built around the LMG1210 driver and two gallium nitride (GaN) FETs in a half-bridge configuration. It is intended for professional development and laboratory work—not as a standalone converter or production assembly.
Because the board uses fast-switching devices and can operate at hazardous voltages, useful measurements depend on both careful setup and disciplined safety practices. Engineers should also distinguish the driver’s capabilities from the limits of the populated evaluation board.
What the LMG1210EVM-012 is designed to evaluate
The EVM provides a compact power stage that can be configured for a buck converter, boost converter or another topology that uses a half-bridge. An external signal generator supplies either a single PWM input or separate high-side and low-side control signals. This arrangement lets engineers examine the LMG1210 as a GaN FET gate driver under selected operating conditions.
Relevant measurements include switching speed, efficiency, slew rate (dv/dt) and adjustable dead time. Since the board is open loop, it is not intended for evaluating converter transient response. The distinction matters: the test setup can characterize switching behavior, but it does not provide a closed-loop control system for studying how a regulated converter responds to changing load conditions.
The driver supports features including independent or PWM input control, adjustable dead time, undervoltage lockout and over-temperature protection. The guide lists operation up to 50 MHz for the driver, but notes that the larger EPC2001 FETs installed on this EVM limit its usable maximum frequency. The board’s specified switching-frequency range reaches 15 MHz under its stated conditions; the actual practical limit depends on the FETs and operating point.
Plan the test around the board’s limits
Before connecting supplies or loads, check the ratings for the complete EVM. The listed input and output voltage range is 0 to 100 V, and the listed input and output current range is 0 to 10 A. The bias supply requirement is 6 to 18 V, with up to 0.3 A. Although the driver is identified as a 300 V half-bridge driver, that designation should not be treated as permission to apply 300 V to this evaluation board: its stated bus limit is 100 V.
The module can deliver up to 10 A when thermal management is adequate. Monitor component and case temperatures, and consider airflow, a heat sink or a lower operating frequency to manage dissipation. The supplied inductor is 4.7 µH with a 10.5 A saturation current, so changing voltage, frequency or desired current ripple may require reassessing the inductor selection.
A typical test bench includes:
- A current-limited DC input supply suitable for the intended voltage and current, up to the board’s 100 V and 10 A limits.
- A 6–18 V bias supply capable of up to 0.3 A.
- A DC electronic load rated for the test voltage and current, plus multimeters or a power meter if efficiency is being measured.
- A function generator for PWM or synchronized independent inputs, and an oscilloscope with suitable probes.
Set up signals and measurements carefully
The EVM supports PWM mode and independent input mode. In PWM mode, a single signal controls the switching sequence, with board potentiometers used to adjust high-to-low and low-to-high dead time. In independent mode, the signal generator provides complementary signals to the high-side and low-side inputs, and dead time is set at the generator.
Do not assume the inputs will prevent both FETs from conducting at once. The guide warns that the board has no automatic protection against cross-conduction. Incorrect dead time can cause unwanted simultaneous conduction and damage the FETs. Set and verify dead time before applying bus voltage, then monitor it across the operating range because the required interval depends on operating conditions.
Fast GaN transitions also make probe technique important. The board’s designated test points are intended for oscilloscope probes with short spring-ground connections, often called pigtails. Using these instead of long alligator-clip ground leads helps reduce measurement error and produce cleaner waveforms. For voltage measurements, Kelvin sense connections provide dedicated points for more accurate readings of the bus and output.
For an efficiency test, connect the instruments and load while supplies are off, configure the selected input mode, and power the bias supply first. Confirm the driver’s internal 5 V LDO is present, enable the signal generator, and check that gate signals do not overlap. Then apply the DC input voltage within the board rating, enable the electronic load, and take measurements. The guide reports a typical 95.1% full-load efficiency for a specified 48 V input, 12 V output, 9 A load and 1 MHz switching condition; those results exclude driver losses.
Make high-voltage safety part of the test procedure
This is an open-frame evaluation module for qualified professionals familiar with electrical hazards. Treat the entire board as potentially live whenever it is energized, and never touch the EVM or its circuits while powered. Components may become hot enough to cause burns, and the board must not be left energized unattended.
Use a clean, orderly work area and a stable, nonconductive surface. Establish barriers and warning signage to prevent inadvertent access, and have a qualified observer present whenever circuits are energized. For development setups exceeding 50 VRMS or 75 VDC, the safety guidance calls for locating the interface circuits, supplies, instruments and related apparatus within a protected emergency power-off (EPO) power strip. Use insulated wiring and clamps, and avoid freehand probing where possible. Isolated test equipment with overvoltage and overcurrent protection is recommended.
De-energize the EVM, its inputs and outputs, and connected loads before making wiring changes or diagnostic measurements. Confirm power is off, but continue to treat the circuit and instruments as electrically live while configuring them. Follow the EVM documentation and use appropriate protective equipment or an interlocked protective enclosure.
Apply the results appropriately
The LMG1210EVM-012 is a development tool for examining GaN half-bridge switching, not a production component or a complete regulated power supply. Its open-loop operation, populated FETs, electrical ratings and thermal needs define what conclusions can reasonably be drawn from a test.
For engineers and system integrators, the practical approach is to establish safe limits first, select the test mode and measurement method deliberately, verify dead time before applying bus voltage, and interpret results in the context of the actual board configuration. Doing so makes the evaluation more useful while keeping high-voltage and fast-switching hazards central to the process.