Access Official Technical PDF

Share Summary:LinkedInEmail

The Toshiba DT01ACAxxx HDD is a 3.5-inch desktop hard disk drive series with formatted capacities from 500 GB to 3 TB. Its published specifications can help engineers and system integrators assess interface compatibility, storage requirements, power budgets and operating conditions. The product overview identifies consumer desktop computers as the intended application, so teams considering the drive for an automation system should distinguish its listed characteristics from any requirements for industrial or continuous-duty service.

Toshiba DT01ACAxxx HDD capacity and interface

The series includes four model numbers: DT01ACA300, DT01ACA200, DT01ACA100 and DT01ACA050, with formatted capacities of 3 TB, 2 TB, 1 TB and 500 GB, respectively. All use a Serial ATA 3.0 interface, also described as ATA-8, with a maximum interface speed of 6.0 Gbit/s. That figure is the interface’s stated maximum, not a guarantee of application-level read or write throughput. Toshiba notes that actual read and write speeds can vary with the host device, operating conditions and file size.

The drives rotate at 7,200 rpm and have an average latency time of 4.17 ms. The overview lists buffer sizes of 64 MiB and 32 MiB for the series, without assigning each value to a particular model in the supplied specifications. These figures help describe the drive’s basic design, but they do not replace testing in the intended host and workload.

Understanding the 512e sector format

The DT01ACAxxx series uses Advanced Format 512e. The stated logical data block lengths are 512 bytes for the host and 4,096 bytes for the disk. In practical terms, the drive presents 512-byte logical sectors to the host while using 4,096-byte physical sectors internally. System designers should confirm that the operating system, storage controller and any software that accesses the drive work correctly with this format.

Capacity figures also need interpretation. Toshiba defines a gigabyte as 1,000,000,000 bytes and a terabyte as 1,000,000,000,000 bytes. Operating systems may report capacity using powers of two, so the displayed usable amount can appear lower than the decimal capacity on the product specification. Formatted capacity may also vary with formatting, settings, software and other system factors.

Power, dimensions and acoustics

The drive requires 5 V within ±5% and 12 V within ±10%. Typical read/write power consumption is listed as 6.4 W. Typical idle consumption is given as 5.2 W and 3.7 W, with the overview showing these as varying figures rather than mapping them to specific models. For an equipment design, use the appropriate supply limits and account for the stated operating condition when reviewing power requirements.

The series has a maximum height of 26.1 mm, a width of 101.6 ± 0.25 mm and a maximum length of 147 mm. Maximum weight is listed as 680 g and 450 g, again without a model-by-model assignment in the overview. The 3.5-inch designation refers to the drive form factor, not its exact physical dimensions; the listed measurements should be used for enclosure and mounting checks.

Sound power figures are provided for idle and seek operation. Depending on the listed configuration, idle sound power is 27 dB or 25 dB, while seek sound power is 28 dB or 26 dB. These values may matter when the drive is installed near operators or in noise-sensitive equipment. The source does not identify which model corresponds to each figure.

Environmental limits and application fit

Specified operating temperature is 0 °C to 60 °C, compared with a non-operating range of -40 °C to 70 °C. Operating humidity is 8% to 90% relative humidity, non-condensing; non-operating humidity is 5% to 95%, also non-condensing. The distinction is important: the broader non-operating limits should not be treated as allowable conditions while the drive is running.

Operating vibration is specified as 6.57 m/s² (0.67 G) from 5 to 500 Hz. Non-operating vibration is 10.2 m/s² (1.04 G) from 2 to 200 Hz. The listed operating shock limit is 686 m/s² (70 G) for a 2 ms half-sine wave. Non-operating shock figures are 2,940 m/s² (300 G) and 3,430 m/s² (350 G), both for a 2 ms half-sine wave. The overview also gives operating altitude as -300 m to +3,048 m and non-operating altitude as -300 m to +12,000 m.

These limits provide selection and design reference points, but the stated application is consumer desktop computing. A proposed automation use should therefore be evaluated against the actual cabinet environment, vibration and shock exposure, operating schedule, host compatibility and the system’s storage needs. The specifications alone do not establish suitability for a particular industrial duty.

Practical selection considerations

  • Capacity: Choose among 500 GB, 1 TB, 2 TB and 3 TB, while allowing for the difference between decimal capacity and operating-system reporting.
  • Host compatibility: Verify SATA 3.0 connectivity and support for the 512e logical and physical sector arrangement.
  • Power and packaging: Check voltage tolerances, typical consumption, physical dimensions and weight against the host design.
  • Environment: Compare expected temperature, humidity, vibration, shock and altitude with the corresponding operating limits.
  • Workload: Treat interface speed as a maximum specification and validate actual behavior under the intended host and file-size conditions.

Conclusion

The Toshiba DT01ACAxxx HDD series combines 3.5-inch packaging, 7,200 rpm rotation, SATA 3.0 connectivity and capacities up to 3 TB. Its sector format, power figures and environmental limits offer useful inputs for technical evaluation. For automation engineers and system integrators, the key is to check those specifications against the complete application—and to remember that the published application is consumer desktop computing, not a blanket qualification for industrial service.

Access Official Technical PDF

About The Author