Access Official Technical PDF

Share Summary:LinkedInEmail

Radiation-hardened mixed-signal ICs sit at the intersection of analogue signal processing, digital control, and the reliability requirements of space systems. The AMICSA 2018 program shows how broad the engineering challenge is: sessions covered radiation effects, circuit and system design, qualification practices, design platforms, and applications ranging from sensors to motor control. For engineers and technical decision-makers, that agenda provides a useful framework for understanding the decisions involved in developing electronics for space missions.

Radiation-hardened mixed-signal ICs: design begins with the environment

Space electronics must be designed and evaluated with radiation effects in mind. The conference program highlighted two distinct concerns: total ionizing dose (TID) and single event effects (SEE). TID describes accumulated radiation exposure, while an SEE is associated with an individual particle interaction in a device. These effects can influence circuit behavior in different ways, so evaluating a component involves more than checking its nominal electrical performance.

AMICSA included presentations on SEE analysis in readout integrated circuits at cryogenic temperatures, radiation characterization of an 18-bit successive-approximation-register (SAR) serial-interface commercial off-the-shelf analogue-to-digital converter, and validation of a high-resolution ADC for space applications. Other listed work addressed total-dose and SEE characterization of a radiation-hardened CMOS ASIC family. Together, these subjects illustrate why radiation response needs to be considered alongside resolution, interface behavior, operating conditions, and the requirements of the intended system.

Testing and qualification connect component performance to mission needs

Testing helps engineers understand how a device behaves under defined conditions; qualification provides a structured basis for determining whether it is suitable for a particular use. The program treated evaluation and qualification as a dedicated topic, including reliability analysis, ESCC single-phase qualification, and characterization, screening, and qualification of a wind-sensor ASIC.

These activities address different stages of confidence-building. Characterization describes device behavior, screening applies checks to identify parts that do not meet specified criteria, and qualification evaluates suitability against an established process. The agenda does not report the outcomes of individual tests, but its coverage makes clear that qualification is not a substitute for understanding the application. Engineers still need to relate device evidence to mission requirements, operating conditions, and the role the component performs in the overall system.

Design platforms and circuit choices shape implementation

Radiation tolerance can be addressed at multiple levels, from transistor-level circuit decisions to libraries, reusable intellectual property (IP), and system architecture. AMICSA’s sessions on custom cell, circuit, and system design included a radiation-hardened low-voltage differential signaling (LVDS) chip, rad-hard microcontrollers, telemetry and telecommand ICs, and a controller implemented in a low-cost plastic package. The program also covered design platforms for specific CMOS processes and an integrated flow for simulating single-event transients (SETs) in a design environment.

For design teams, the practical point is that technology selection and implementation methods are connected. A process, cell library, or IP block can influence what circuit options are available, while the system’s functions determine which interfaces and protections matter. The listed work on design platforms, analog IP, and SET simulation reflects a focus on making radiation-aware design and evaluation part of the development workflow—not treating radiation as a final check after the circuit is complete.

Space applications span sensing, imaging, power, and control

The program’s application sessions show the variety of roles analogue and mixed-signal electronics can play in space systems. Listed topics included solar irradiance sensing on Mars, Earth-observation imaging using time-delay integration, and a detector readout ASIC for cold solar-wind analysis. Other presentations addressed a fault-tolerant power management and distribution system using radiation-hardened analogue front ends, as well as a rad-hard system-on-chip for closed-loop motor control.

These examples involve different signals, interfaces, and system responsibilities. Sensor readout and signal conditioning must connect physical measurements to downstream electronics; imaging systems process information from detector arrays; power-management circuitry supports electrical distribution; and motor-control electronics participate in feedback loops. The agenda does not provide design results or comparative performance data, but the breadth of applications underscores why component requirements should be defined in system context.

What automation and electronics teams can take from AMICSA

Although the conference focused on space applications, its engineering themes are relevant to teams responsible for selecting and integrating specialized electronics. A disciplined review can include:

  • Application requirements: Define the device’s function, interfaces, and operating conditions before comparing candidate components.
  • Radiation evidence: Determine which radiation effects have been evaluated and whether the available characterization matches the intended use.
  • Development approach: Consider how process technology, libraries, IP, and simulation methods fit the design workflow.
  • Qualification plan: Distinguish characterization, screening, and formal qualification, and establish what evidence is required for the system.
  • System integration: Assess how the IC interacts with sensors, power electronics, communication links, and control functions.

Conclusion

AMICSA 2018’s program presented radiation-hardened mixed-signal IC development as a connected engineering discipline: radiation effects influence circuit design, test and qualification support component assessment, and application requirements shape implementation choices. For technical decision-makers, the practical implication is to evaluate devices as part of a defined system and mission context. That approach helps align component selection, design methods, and verification activities with the requirements the electronics must meet.

Access Official Technical PDF

About The Author