Access Official Technical PDF

Share Summary:LinkedInEmail

A modular safety controller brings configurable safety logic together with the sensors and actuators that help protect people and equipment on a machine. The Schneider Electric XPSMCMCP0802x provides eight safety-related digital inputs and two safety-related outputs, with expansion options for larger configurations. Applying it safely requires more than selecting modules: the complete system must be designed, configured and validated against the risks and standards relevant to its application.

What the XPSMCMCP0802x modular safety controller does

The XPSMCMCP0802x is configured using SoSafe Configurable software and a USB connection to a computer. Its eight inputs can connect devices such as safety sensors and push-buttons. The controller also provides two pairs of OSSD (Output Signal Switching Device) channels, which are solid-state safety outputs. Expansion modules can be connected through a backplane bus to extend the system.

The product documentation identifies safety capability values including SIL 3, SILcl 3, and PL e, Category 4, under the referenced standards. These figures do not automatically establish the achieved safety level of a machine. The application’s final SIL or performance level depends on the complete set of safety-related components, their parameters, wiring and architecture, as determined through risk analysis.

Configuring safety inputs and outputs

Safety inputs and test outputs

Input monitoring is set up in SoSafe Configurable. To support the stated Category 4 and SILcl 3 architecture, inputs must be supplied by the controller’s line-control test outputs. These outputs are configured in the software and used to detect conditions such as short circuits or overloads on input circuits. The controller provides four test outputs for this purpose.

Correct device selection and wiring matter: the controller’s input-monitoring design depends on the connections and configuration used in the application. The installer or user is responsible for configuring the module in accordance with the application-specific risk analysis and applicable standards.

OSSD and status outputs

The two OSSD outputs are safety-related semiconductor outputs, with two physical channels per output. The documentation specifies that the paired channels are required to achieve a Category 4 architecture with connected outputs. Output monitoring uses pulses on each channel to detect short circuits and line breaks; the specified pulse interval and duration are part of the product’s technical characteristics.

The controller also has two configurable STATUS outputs for diagnostic indications. These are non-safety-related outputs and must not be used to perform a safety function. Treating a diagnostic signal as a safety output would give it a role the product documentation does not assign to it.

Restart, enable and external device monitoring

Both master-enable inputs must be at logic level 1 (24 Vdc) for the controller to operate. Removing the supply to these inputs sets them to logic level 0 (0 Vdc) and disables the controller.

The RESTART inputs support manual or automatic operation and can be configured to monitor an EDM (External Device Monitoring) feedback signal from external contactors. If a restart command is used, it must be positioned outside the operating zone, where the relevant work area is clearly visible, and must not be operable from within that zone. The restart arrangement and its relationship to the machine’s risk controls must be validated as part of the complete system.

Installation and configuration safeguards

Installation, operation and maintenance should be performed by qualified personnel. Before working on the equipment, disconnect power to the controller and connected devices, allow stored energy in drives or contactors to discharge as directed by their instructions, and verify the absence of voltage with appropriately rated equipment. Follow applicable electrical safety procedures, including lockout/tag-out where required.

The documentation also specifies important installation conditions:

  • Install the controller system in an enclosure with at least IP54 protection, and use an isolated PELV power supply.
  • Use a common 0 Vdc supply for modules in the Modular Safety Controller family.
  • Install and use the equipment only in non-hazardous locations, and do not use it to supply external drives or contactors.
  • Mount the modules on a 35 mm DIN rail. Maintain at least 40 mm clearance above and below and at least 100 mm between the module front and cabinet door.
  • Use 60/75 °C copper conductors. Connection cables longer than 50 m require a cross-section of at least 1 mm²; the stated maximum cable length is 100 m.

Observe the controller’s rated operating limits and ambient conditions. Equipment exposed to electrical, mechanical or environmental stresses beyond its specified limits should not remain in service.

Memory card use and system validation

An optional XPSMCMME0000 memory card can store and restore a configuration. The card is specific to the XPSMCMCP0802x. If it contains a configuration that differs from the one in the controller, inserting it and powering the system can overwrite the controller’s existing configuration, including its password. Remove controller power before inserting or removing the card, and verify that the configuration loaded is the one intended for the machine.

After using the card to overwrite an application, conduct a full functional test of the controller and all connected input and output hardware. The same principle applies during commissioning: check wiring and terminal security, confirm relevant input and output indicators, verify sensor and actuator positions and operation, and test external indicators. The project’s response time should be taken from the SoSafe Configurable project report because it varies with configuration, including expansion modules and input filtering.

Practical implications for machine builders and plant teams

The XPSMCMCP0802x offers a configurable foundation for machine safety functions, but its ratings are not a substitute for application engineering. For integrators and plant teams, the key steps are to carry out a risk assessment, select and wire suitable devices, configure monitoring and restart behavior, and validate the complete machine against its required safety performance. Careful control of configuration changes, especially when using a memory card, helps ensure that the safety logic in the controller matches the intended application.

Access Official Technical PDF

About The Author