Lightning protection systems are essential to managing risk at industrial facilities, commercial buildings and other sites where a strike could threaten people, structures or equipment. But protection depends on more than installing a rod on a roof. The system must be designed as an integrated path that intercepts a strike and conducts its energy safely to ground, while separate measures address lightning-related surges in electrical and electronic systems.
Misunderstanding how these measures work can create a false sense of security. For engineers, integrators and facility managers, the practical priorities are to follow recognized design guidance, use qualified expertise and distinguish structural lightning protection from surge protection.
How lightning protection systems work
A conventional lightning protection system uses air terminals—often Franklin rods—to provide points where a strike to the protected structure can be intercepted. The terminals do not attract lightning, dissipate it or force it away. Properly designed and installed, the system provides a controlled route for lightning current to travel around the structure and into the earthing system.
The effectiveness of protection comes from the arrangement and connection of its components, not simply from adding more points to a roof. A building’s system generally includes:
- Air terminals: Positioned to intercept lightning that would otherwise strike the structure.
- Down-conductors: Conduct the intercepted current toward the earthing system. The advisory describes a minimum of two down-conductors for a building.
- Earthing: Provides a route for current to enter the ground. Depending on site conditions, this may use driven metal electrodes or a buried ring conductor bonded to the down-conductors.
- Bonding or separation: Helps coordinate the system’s components and manage electrical potential differences.
These elements must work together. A rod without suitable conductors, earthing and connections does not constitute a complete protection system. Site conditions also matter: for example, the advisory notes that a buried conductor ring may be practical where dry soil makes driven electrodes more challenging.
Lightning protection design: separate structural and electrical risks
Structural lightning protection and protection for electrical equipment address related but different hazards. The air terminals, down-conductors and earthing system are intended to manage a direct strike to a structure. Surge protection devices (SPDs), along with measures such as cable shielding and appropriate installation practices, address lightning’s induced effects on electrical and electronic systems.
Surge protectors should not be treated as a substitute for a building lightning protection system. They may help protect connected appliances and equipment when appropriately selected and installed, but they do not protect a building from a direct strike. Facilities with sensitive electronics or costly electrical systems may need both structural protection and coordinated surge protection.
This distinction is particularly relevant in industrial environments, where a facility’s protection plan must account for the building as well as the electrical and electronic systems within it. The required measures should be determined through an appropriate design process rather than assumptions about what one device can protect.
Question claims that promise more protection
Lightning protection is a specialized discipline, and unfamiliarity with its engineering requirements can make facilities vulnerable to misleading claims. The advisory challenges the idea that multiplying the number of points on an air terminal automatically multiplies its effectiveness. It also warns against products promoted as lightning dissipators or devices that claim to repel, weaken or capture lightning across an unusually large area.
Decorative features, extra tips or claims about emissions do not by themselves demonstrate that a system provides better protection. The advisory states that claims made for early streamer emission (ESE) and semiconductor lightning eliminator (SLE) products—including claims of expanded protection zones or reduced lightning current—have been disputed by scientific studies. Buyers should seek evidence of standards compliance and a defensible engineering design rather than rely on marketing language.
Nor should a single rod be assumed to protect an entire compound with multiple buildings. Each structure and its exposure need to be considered in the design. A system that leaves buildings or people outside its intended protection can create misplaced confidence, which is itself a safety concern.
Use IEC 62305 as a design framework
IEC 62305 provides a structured approach to lightning protection. Its four parts address complementary aspects of the work:
- Part 1: General principles and information about lightning and its characteristics.
- Part 2: Risk management, including analysis used to evaluate risk and compare protection scenarios.
- Part 3: Physical damage to structures and life hazards, including direct strikes, side flashes, step potential and touch potential.
- Part 4: Protection of electrical and electronic systems within structures from lightning’s induced effects.
Part 3 treats air termination, down-conductors, earthing and equipotential bonding or separation as elements of an integrated system. Part 4 addresses measures such as SPDs, cable shielding and installation rules. The IEC 61643 series covers SPDs, while the IEC 60364 series includes requirements relevant to their application in low-voltage electrical installations.
For technical decision-makers, the standard’s risk-management approach is important: protection choices should follow an assessment of the structure and its risks, rather than a one-size-fits-all product claim. Design, component selection, installation and coordination all need attention.
Make protection a managed engineering responsibility
Lightning protection work should be handled by people with relevant expertise and familiarity with applicable standards. Electrical engineering experience alone does not necessarily include specialist training in lightning protection. Owners and project teams should verify that a proposed design addresses the entire system, identifies the structures and equipment covered, and distinguishes direct-strike protection from surge protection.
Public awareness and local standards also matter. The advisory highlights the role of regulators, meteorological authorities and emergency-response organizations in addressing different parts of the lightning hazard. For facilities, this reinforces the need to connect engineering controls with operational awareness and appropriate response planning.
Conclusion
Reliable lightning protection is not a matter of choosing the most elaborate-looking terminal or trusting claims of a larger protection radius. It requires a coordinated system of air terminals, down-conductors, earthing and bonding, designed for the structure and informed by recognized guidance such as IEC 62305. Where electrical and electronic equipment is at risk, surge protection must be considered as an additional, distinct measure. For industrial facilities, the practical takeaway is clear: verify the design, the standards basis and the limits of every protection measure before relying on it.