Access Official Technical PDF

Share Summary:LinkedInEmail

A continuous gas analyzer can provide process teams with measurements of multiple gas components, but dependable operation begins well before the first reading. The Rosemount CT5400 is a configurable process gas analyzer that uses mid-infrared laser spectroscopy to measure selected gases in a sample stream. For engineers and plant teams, understanding the boundary between the analyzer and the supporting gas-handling system is central to planning an installation and managing its safe operation.

How the Rosemount CT5400 measures process gas

The CT5400 directs light from quantum cascade lasers (QCLs) through an optical path and into a heated, multi-pass analysis cell. As the light passes through the sample, target gas molecules absorb light at characteristic wavelengths. A receiver measures the light that exits the cell, and the analyzer determines gas concentrations by analyzing the absorption features with a spectral fitting routine.

The optical path through the cell is extended by multiple reflections, providing a path length of between 2 m and 5 m. The analyzer can be configured to measure up to twelve gas types, depending on the laser modules fitted. The gases measured and their concentration ranges depend on the system configuration; the instrument is described as measuring concentrations from parts per million (ppm) to percentage levels.

This measurement approach does not mean the analyzer prepares the sample. The CT5400 has no internal sample-conditioning system. The external gas-handling system must condition and deliver the sample within the analyzer’s specified parameters before it enters the cell.

Plan the analyzer and sample-handling system together

A complete installation includes the analyzer, a gas-handling system, sample supply and return lines, interconnecting wiring and a connection to the control center. The analyzer provides measurement data, while the site supplies the supporting equipment and connections. That division of responsibility should be established during project planning, particularly for sample conditioning, calibration gas provisions and data integration.

The analyzer is designed for a standard 482.6 mm (19 in.) rack and is intended for indoor use. Its ventilation openings must remain unobstructed, and the installation location should provide suitable shelter from environmental elements and water. The instrument weighs approximately 31 kg, so moving and rack mounting require appropriate lifting practices; the manual recommends at least two people.

Before installation, confirm that utilities and process connections match the instrument requirements. The manual specifies a 240 Vac, 50 Hz supply, and the analyzer must be connected to a properly grounded three-wire power source. The sample inlet and return ports are on the rear panel. The sample supply line must be heated all the way to the analyzer inlet to help prevent condensation in the line.

Check process conditions and limits

Sample gas conditions are part of the installation design, not an adjustment that can be left to the analyzer. The stated process-gas flow limit is 6 L/min. The manual also specifies operating and sample conditions, including an ambient operating range of 0 to 45 °C and a sample-gas temperature range of 50 to 195 °C, with the sample temperature range factory-set and specified on order. Confirm the requirements for the particular instrument configuration before commissioning.

Safe-use conditions also restrict the gas groups and composition for which the equipment is intended. The manual states that process gases must be in the specified gas groups and must not contain oxygen or another oxidizer at concentrations above those found in normal air. The equipment is not intended for use with flammable liquids. Site-specific requirements and applicable local regulations must be considered alongside the instrument instructions.

Use trained personnel and formal safety procedures

Installation, operation, maintenance and service require personnel with suitable instrumentation and control knowledge, training on the analyzer, and authorization for the hazardous-area work involved. Operators should read and understand the relevant manual sections and know the site safety procedures before beginning work. Where instructions are unclear, the manual directs users to seek guidance from the manufacturer or its distribution partners.

Several hazards require explicit controls:

  • Electrical energy: The analyzer uses mains voltage. Isolate and tag the power before removing covers, maintain protective covers during operation, and ensure the instrument is earthed.
  • Process gas: Sample gas may be hazardous, including at low concentrations. Route the return stream to the process or to a location where it will not create a hazard.
  • Maintenance isolation: Lock out the gas-handling system and associated supplies before maintenance. Follow site procedures to vent and purge sample gas; the manual specifies allowing the return system to run for five minutes so gas can be returned to the exhaust.
  • Hot surfaces and lifting: Some internal parts can become hot, and the instrument is heavy. Use suitable handling equipment and protective practices.

The lasers are classified as Class 1, but that does not remove the need to follow the prescribed procedures. The manual warns against viewing laser light with magnifying or optical measuring devices and against performing unauthorized adjustments.

Commissioning, operation and maintenance

Before startup, verify that the analyzer is physically secure and that the electrical and pneumatic connections are in place. Confirm the availability of electrical power, sample-handling facilities and any calibration gases required for the application. Follow the documented startup procedure: the manual cautions that incorrect startup or missed pre-start checks can damage the equipment. It gives a warm-up time of 90 minutes.

During normal operation, measurement data can be displayed in the process control center, subject to the system’s configured outputs and connections. The CT5400 can be ordered with four or eight 4–20 mA measurement-result channels. These details make it important to confirm signal requirements and system interfaces during design rather than assume that every installation has the same configuration.

Maintenance should be performed by qualified personnel following the applicable procedures. The manual includes verification and calibration procedures, built-in-test diagnostics, troubleshooting guidance and scheduled preventative maintenance. Used gas-handling components may contain residues from the sample stream; handle them cautiously, use appropriate protective equipment and package contaminated items for disposal according to applicable regulations. Replacement parts and procedures should be those specified by the manufacturer.

Conclusion

The Rosemount CT5400 combines QCL-based mid-infrared absorption measurement with a configurable, multi-gas optical system. Its performance in a plant depends on more than the analyzer itself: the sample must be properly conditioned, gas lines and utilities must meet requirements, ventilation must remain clear, and installation and service must be carried out by trained personnel. Treating these elements as one system gives engineering and operations teams a practical foundation for safer commissioning, consistent operation and maintainable process gas analysis.

Access Official Technical PDF

About The Author