Access Official Technical PDF

Share Summary:LinkedInEmail

Flame detector testing is an important part of verifying that a fire protection system can respond as intended. The SPECTREX FS-1200 UV/IR Flame Simulator provides a portable way to test compatible SharpEye detectors without creating an actual fire. Its emitted UV and IR energy is arranged in a sequential pattern recognized by supported detector models, allowing teams to check detector response and related system functions under simulated fire conditions.

For industrial facilities, the practical value of this approach is that a functional test can exercise more than the detector sensor alone. When performed as part of an end-to-end test, it can help verify alarm activation, wiring and configured outputs. Because a test may trigger alarms or an extinguishing system, planning and site procedures remain essential.

What the FS-1200 tests

The FS-1200 uses a halogen lamp to emit UV and IR energy. A reflector directs that energy toward the detector. The simulator has a mechanical sight for aiming; it does not use a laser diode. Operators aim the device at the center of the detector and use the visible spot to refine alignment.

The simulator is listed as compatible with SharpEye models 40/40L-LB, 40/40L4-L4B, 40/40U-UB, 40/40UFL and 20/20ML. Confirm compatibility before starting a test, and check the detector’s sensitivity setting and operating condition if the expected response does not occur.

A properly planned test can assess detector response and, as applicable to the installed system, alarm software, relay activation and other outputs such as mA, RS-485 or HART. It can also reveal issues such as a dirty detector viewing window. The simulator itself does not replace inspection or maintenance of the detector or the wider fire protection system.

Planning flame detector testing with the FS-1200

Testing can activate alarms or suppression equipment. Before beginning, determine whether these outputs should operate during the test. If not, disconnect or inhibit them in accordance with site procedures, then restore them after testing. Keep the simulator aimed at the detector for up to 50 seconds, or until an alarm is triggered. Allow a 20-second interval before another activation.

Test distance depends on the detector model and sensitivity. The guide gives these pairings:

  • 40/40U-UB, 40/40L-LB and 20/20ML: detector sensitivity setting 50 ft (15 m); testing distance 20 ft (6 m).
  • 40/40L4-L4B: detector sensitivity setting 93 ft (28 m); testing distance 8 ft (2.5 m).
  • 40/40UFL: detector sensitivity setting 60 ft (20 m); testing distance 23 ft (7 m).

The minimum distance from the detector is 30 in (75 cm). At extreme temperatures, the guide notes a 15% reduction in testing range. Use the correct distance for the detector being tested rather than assuming that one setup applies to every model.

Hazardous-area and battery precautions

The FS-1200 is certified for specified hazardous-area applications. Its ATEX and IECEx marking identifies use in Zone 1 and Zone 2 environments with the stated IIB + H2 gas group and temperature classification. Confirm that the equipment marking and site requirements match the intended location; certification details and permitted conditions should be checked against the applicable documentation.

Do not open the simulator in a hazardous area. Charging requires removing the battery from the flameproof enclosure and must take place in a safe area. The guide specifies a maximum charge voltage of 4.2 V per cell and maximum charge current of 2200 mA. It also directs users to charge the unit in a safe area at no more than 104°F (40°C), and to use the charger supplied with the simulator.

Use only the specified SPECTREX replacement battery pack, part number 380004. The battery pack contains four lithium-ion cells and is rated at 14.8 V and 2.2 Ah. The guide states that a full charge supports at least 100 tests and gives a charging duration of two to three hours in the operating instructions. Follow the unit’s instructions and site battery-handling procedures; do not modify or attempt to repair the simulator’s internal circuits.

Inspection, maintenance and troubleshooting

Before use, ensure the simulator is charged and check that its reflector and window are clean. When stored and not in use, recharge the battery at least every six months. The device is not field-repairable: sensor and circuit alignment are carefully calibrated, and internal modifications can impair performance.

If the light does not turn on, the guide identifies low battery, a halogen fault or total failure as possible causes. Recharge the battery first; if necessary, replace it with the approved pack. If the simulator operates but does not activate the detector, check the test distance, detector sensitivity, detector operation, and cleanliness of the detector window and simulator reflector. If these checks do not resolve the issue, send the simulator for repair rather than opening it in the field.

Make each test part of a controlled maintenance process

The FS-1200 supports functional checks without the hazards associated with an open flame, but reliable results depend on correct compatibility, distance, aiming and battery condition. Coordinate alarm and suppression-system handling before the test, follow hazardous-area restrictions, and document and restore any inhibited outputs. Treating the simulator as one element of a planned end-to-end maintenance procedure helps teams verify detector response while preserving safe operating conditions.

Access Official Technical PDF

About The Author