Access Official Technical PDF

Share Summary:LinkedInEmail

Pressure measurement is a foundation of industrial automation. It helps operators monitor process conditions, protect equipment and, in some applications, determine flow from a pressure difference. Steam, feedwater, compressed air, hydraulic systems and lubrication circuits all rely on pressure instruments, but selecting the right device requires more than matching a measurement range.

Engineers and system integrators must also consider the pressure reference, process medium, operating environment, control purpose and installation details. Understanding how gauges, regulators, switches and differential pressure transmitters work makes it easier to choose and maintain instruments that provide useful, dependable process information.

Pressure measurement starts with the reference

Pressure is force acting over an area: pressure equals force divided by area. It may be expressed in pascals (Pa), kilopascals (kPa), megapascals (MPa) or pounds per square inch (psi). The reference used for a reading is equally important because atmospheric pressure changes with altitude and weather conditions.

  • Gauge pressure is measured relative to local atmospheric pressure.
  • Absolute pressure is measured relative to a vacuum. Absolute pressure equals gauge pressure plus atmospheric pressure.
  • Differential pressure is the difference between pressures at two points.

These references are not interchangeable. Confirming whether a process value is gauge, absolute or differential pressure helps prevent errors in instrument selection, control logic and operator interpretation.

Pressure measurement technologies

Pressure instruments use mechanical or electrical sensing elements. Mechanical options include manometers, Bourdon tubes, diaphragms and bellows. Electrical approaches include strain-gauge, capacitive, resonant-wire, piezoelectric, magnetic and optical sensors.

A manometer balances the pressure difference against the weight of a fluid column. It is useful for understanding or measuring pressure differences, particularly in laboratory settings. A Bourdon tube is a curved, hollow metal element that moves as pressure changes. A mechanical linkage converts that movement into pointer motion on a dial. Diaphragms and bellows also respond to pressure through physical movement and can be useful where compact construction or material compatibility is important.

Electronic sensing methods have different operating characteristics. Strain-gauge sensors detect the deflection of an elastic diaphragm, while capacitive sensors detect changes in capacitance as a diaphragm moves. Resonant-wire devices translate pressure-induced changes in wire tension into a frequency change. Piezoelectric sensors are suited to dynamic pressure changes, but their charge decays, making them unsuitable for static pressure measurement. The application, expected pressure range and required measurement behavior should guide the choice.

Choosing and installing industrial pressure gauges

Pressure gauges provide a local indication of process pressure and may be mechanical or electronic. For a Bourdon-tube gauge, pressure causes the tube to flex; a gear mechanism transfers that movement to the pointer. Dry gauges are common, while liquid-filled designs use fluid in the case to damp pointer movement and help reduce the effects of vibration and condensation.

When selecting a gauge, consider the maximum anticipated pressure, readability, connection location, process medium and environmental conditions. The source recommends choosing a range that is about twice the maximum anticipated pressure, with maximum operating pressure not exceeding 80% of full scale. Select a dial size that can be read at its installed location and confirm that wetted materials are suitable for the service.

Installation affects both instrument life and measurement usability. Mount gauges where they can be read and serviced, and minimize impulse-line length. Avoid locations subject to severe vibration, moisture or extreme ambient temperatures. Where vibration is high, remote mounting with flexible tubing may be appropriate. Provide an isolation valve so the gauge can be inspected or replaced without shutting down the process. Tighten the fitting using the gauge socket flats, not the case, and use a suitable thread sealant where required.

Regulators and pressure switches serve different roles

A pressure regulator is a self-contained mechanical control loop: a sensing element, controller and valve work together to maintain downstream pressure without an external energy source. Because regulators use proportional-only action, a change in flow demand can shift the regulated pressure. This offset is known as droop. Oversizing is a common selection error: although a larger regulator may offer more capacity, it can also lead to poor regulation, seat wear and higher cost. Sizing should account for maximum flow at minimum pressure drop, with the aim of operating around 50–60% open under normal conditions.

A pressure switch converts a pressure condition into an electrical state change. When pressure reaches its set point, contacts open or close; they return when pressure crosses the reactivation point. The difference between actuation and reactivation is the differential, or dead band. Dead band helps prevent frequent switching, or “hunting,” as pressure fluctuates near the set point.

Switch selection should account for the process medium and actuator compatibility, set point, switching function, electrical load and enclosure. The electrical rating must exceed the rating of the device being controlled. Enclosure choice should match the installation environment and any applicable hazardous-location requirements.

Differential pressure transmitters and calibration

A differential pressure transmitter senses pressure at two points and converts the measured variable into a standardized output signal. One described application measures vessel gas pressure by venting the low-pressure side to atmosphere and connecting the high-pressure side to the vessel. A differential pressure transmitter can also support flow measurement when pressure difference is used as the flow indication.

Calibration helps verify that an instrument’s indication or switching behavior corresponds to a known reference. A dead-weight tester applies known pressure using a weight and piston over a precisely known area. For a pressure gauge, readings can be recorded across increasing and decreasing pressure to assess error and response. Pressure switches can be tested by slowly increasing and decreasing applied pressure and recording the opening and closing points.

Practical implications for plant teams

Reliable pressure instrumentation depends on matching the device to the measurement task and maintaining it in its installed context. Confirm the pressure reference and range, account for process and environmental conditions, provide suitable isolation and mounting, and verify performance with an appropriate calibration method. These steps help engineers, integrators and operations teams use pressure data more effectively for monitoring, control and equipment protection.

Access Official Technical PDF

About The Author