A continuous gas analyzer can provide process teams with ongoing measurements of gas composition, but its performance depends on more than the analyzer itself. Sample handling, installation conditions, controls integration, and safe maintenance all affect how the measurement system operates. The Rosemount CT5800 is designed for industrial process gas analysis, using laser spectroscopy to measure configured gases at concentrations ranging from parts per million (ppm) to percentage levels.
How the Rosemount CT5800 measures process gas
The CT5800 uses mid-infrared optical absorption spectroscopy. Its laser sources sweep across wavelengths that include the absorption lines of the target gases. As light passes through the sample in a heated, multi-pass analysis cell, the gases absorb light at characteristic wavelengths. The analyzer measures changes in light intensity and applies spectral fitting to determine gas concentrations.
The instrument can be configured to detect and measure as many as 12 gas types, depending on the combination of laser modules installed. The gases that can be measured are therefore configuration-dependent; the analyzer is not a universal detector for every possible gas. Laser modules may use quantum cascade, interband cascade, or tunable diode lasers, according to the system configuration.
This optical measurement takes place inside the analyzer, but preparing the gas for measurement is an external system responsibility. The CT5800 does not provide sample conditioning. A separate gas handling system must deliver a sample that meets the analyzer’s specified pressure, temperature, and other requirements before it enters the analysis cell.
Plan the complete gas analysis system
A functioning installation combines the analyzer with the sample supply and exhaust lines, gas handling equipment, power, interconnecting wiring, and a connection for measurement data to the control center. Depending on the installation, the gas handling system may be supplied by the customer or by Emerson. Other components, including reference gas cylinders and associated regulators, may also be customer-supplied.
During project planning, engineers and system integrators should define the responsibilities and interfaces for each part of the system. Key considerations include:
- Sample suitability: Confirm that the gas delivered to the analyzer falls within the applicable operating parameters. Conditioning must be provided outside the analyzer.
- Gas routing: Plan the sample inlet, sample return, and exhaust paths. The sample return must discharge to the process or another location where it will not create a hazard.
- Calibration provisions: Identify the required reference gases, cylinders, regulators, and pneumatic connections for the intended measurements.
- Power and data: Provide the specified electrical supply and the wiring needed to communicate measurement data to the control system.
- Mounting and access: Select a solid, stable wall or frame that can support the analyzer and allow qualified personnel to access it for operation and maintenance.
The CT5800 weighs 80 kg, so handling and mounting require suitable lifting equipment and an appropriate support structure. The manual cautions against mounting it on stud or partition walls and recommends that at least two people move and lift it using suitable equipment. Vibration and excess low-frequency disturbance should also be considered when choosing a mounting location.
Hazardous-area design and installation requirements
The analyzer has a flameproof enclosure and is intended for industrial applications that require hazardous-area protection. The manual describes a design for ATEX Zone 1 applications and identifies Ex d protection. Suitability for a particular site must still be confirmed against the equipment’s certification, process-gas characteristics, local requirements, and installation conditions. The presence of a hazardous-area enclosure does not remove the need to follow the applicable safety procedures.
Some certification conditions in the manual specify that process gas flow must be limited to a maximum of 6 litres per minute and restrict the permitted gas groups and oxidizer content. These conditions apply to the relevant certification and installation; engineers should consult the applicable certificates and instructions rather than assume a single set of limits covers every configuration.
Installation, commissioning, operation, and service should be performed by trained, authorized personnel familiar with the analyzer and hazardous-area procedures. Follow the applicable manuals, site rules, and national and local codes. Use only manufacturer-authorized replacement parts where specified, and do not open the analyzer while energized or in an explosive atmosphere.
Build safety into operation and maintenance
Gas analysis systems can present hazards even when connections have been made correctly. The sample or exhaust may contain toxic or flammable constituents, and gas connections must be airtight and routed to suitable locations. Before opening gas lines for service, purge them with air or an appropriate neutral gas in accordance with site procedures. Lock out the gas handling system and isolate relevant supplies before maintenance, preventing an unintended release of process or calibration gas.
Electrical and thermal hazards also require attention. The analyzer operates from mains voltage, and its internal parts can reach 60 °C. The manual directs personnel to isolate power before opening the cover and to allow the analyzer to cool before maintenance; it specifies longer cooling before work on or near the insulated analysis cell. The unit contains enclosed Class 1 lasers, but opening it or performing procedures outside those specified can create an optical radiation hazard.
Startup and shutdown are controlled procedures, not informal switching steps. Confirm that the analyzer is securely mounted and that electrical and pneumatic connections, sample handling facilities, and required calibration gases are available before startup. Follow the specified sequence to avoid equipment damage. If the analyzer is out of order, isolate inputs and outputs connected to external equipment as directed in the manual.
Practical implications for project teams
The Rosemount CT5800 combines laser-based measurement with a separate sample handling system and process control interface. For engineers and operations leaders, the central planning task is to treat these elements as one measurement installation: select a suitable analyzer configuration, prepare the sample externally, define gas routing and calibration arrangements, and verify that mounting, wiring, and hazardous-area conditions meet the applicable requirements.
Careful commissioning and disciplined maintenance help protect both measurement equipment and personnel. Review the instrument’s current manuals and certification documents for the specific installation, and ensure that only qualified personnel perform work on the analyzer or its gas connections. These steps provide the foundation for integrating continuous process gas measurements safely into industrial operations.