A 150 V MOSFET can be a useful building block in DC-DC conversion, but selecting one requires more than comparing its headline current rating or on-resistance. Engineers must also assess gate-drive conditions, switching behavior, thermal paths, and the limits under which device specifications were measured. The onsemi FDMS86200 family is an N-channel shielded-gate MOSFET designed to combine low on-state resistance with switching performance for power-conversion applications.
Where the FDMS86200 fits in a power design
The FDMS86200, FDMS86200-NC, and FDMS86200-TE-NC are listed as 150 V devices in a Power 56 PQFN8 package. The stated application is DC-DC conversion. Its POWERTRENCH process incorporates shielded-gate technology, and the device is optimized for on-state resistance while maintaining switching performance.
For design teams, this makes the part relevant to evaluation in power stages where drain-to-source voltage capability, conduction loss, and switching behavior all matter. The data sheet does not define a particular converter topology or guarantee performance in a specific design. Suitability depends on the circuit, operating conditions, layout, thermal management, and validation in the intended application.
Understanding the electrical ratings
The maximum drain-to-source voltage, VDS, is 150 V, while the gate-to-source voltage, VGS, is rated at plus or minus 20 V. These are maximum ratings, not recommended operating targets. Exceeding maximum ratings may damage the device, affect reliability, or prevent normal operation.
Current ratings also need careful interpretation. At a case temperature of 25 °C, the listed continuous drain current is 35 A. The continuous rating at an ambient temperature of 25 °C is 9.6 A under the data sheet’s stated mounting conditions. A pulsed drain current of 100 A is also specified, but a pulsed rating should not be treated as an allowable continuous load. Actual current capability depends on thermal conditions and the application circuit.
On-resistance depends on gate drive and temperature
The maximum static drain-to-source on-resistance is 18 mΩ at a gate drive of 10 V and a drain current of 9.6 A. At 6 V gate drive and 8.8 A, the maximum is 21 mΩ. The data sheet also gives a maximum of 34 mΩ at a junction temperature of 125 °C under the 10 V, 9.6 A test condition.
These figures illustrate why it is important to compare specifications at conditions that match the intended design. A controller’s gate-drive voltage and the MOSFET’s junction temperature both affect the resistance used when estimating conduction losses. Typical values can support initial analysis, but they should not replace evaluation against maximum limits and the application’s operating range.
Switching data and gate-drive considerations
At the stated test conditions of VDD = 75 V, ID = 9.6 A, VGS = 10 V, and a 6 Ω gate resistance, the typical turn-on delay is 13 ns and rise time is 7.9 ns. Typical turn-off delay and fall time are 27 ns and 5.8 ns, respectively. These are test results, not universal switching times: circuit parasitics, driver strength, gate resistance, voltage, current, and temperature can change switching behavior.
The typical total gate charge is 33 nC when the gate is driven from 0 V to 10 V at the specified 75 V and 9.6 A conditions. For a 0 V to 5 V drive, the typical value is 18 nC under the listed test conditions. Gate charge is relevant when assessing driver requirements and switching transitions, but system-level performance must be checked in the actual circuit.
Capacitance data provide additional context for switching analysis. At VDS = 75 V, VGS = 0 V, and 1 MHz, typical input, output, and reverse-transfer capacitances are 2041 pF, 203 pF, and 10 pF, respectively. Because these values are tied to specified measurement conditions, they should be treated as reference points rather than fixed values across all operating voltages.
Thermal design and safe operating limits
The junction-to-case thermal resistance is listed as 1.2 °C/W. Junction-to-ambient thermal resistance is 50 °C/W for the specified board arrangement: a 1 in², 2 oz copper pad on a 1.5 × 1.5 in. FR-4 board. The data sheet notes that the board design determines the case-to-ambient thermal resistance. Consequently, the listed junction-to-ambient value should not be assumed for a different PCB layout or copper area.
Maximum power dissipation is 104 W at a case temperature of 25 °C, compared with 2.5 W at an ambient temperature of 25 °C under the stated conditions. These ratings are not interchangeable: the case-temperature rating assumes a defined thermal reference, while the ambient rating reflects a different heat-removal path. The maximum operating and storage junction-temperature range is −55 °C to +150 °C.
Design reviews should account for conduction and switching losses together, then check the resulting junction temperature against the device limits. The data sheet includes safe-operating-area and transient-thermal-response curves to support evaluation across different pulse durations and operating conditions.
Practical selection checklist
- Confirm that the maximum drain voltage and gate-drive voltage remain within device ratings, with suitable allowance for circuit conditions.
- Use the on-resistance value associated with the intended gate voltage, current, and temperature when estimating conduction losses.
- Evaluate switching behavior and gate-drive requirements using the application circuit rather than relying only on datasheet test values.
- Model the actual PCB and heatsinking arrangement; thermal performance depends on the design and mounting conditions.
- Check pulsed operation against the safe operating area and transient thermal data, and do not treat a pulsed current rating as continuous capability.
Conclusion
The FDMS86200 family offers a 150 V rating, shielded-gate construction, and specified on-resistance and switching characteristics for evaluation in DC-DC conversion designs. Its ratings are useful starting points, not a substitute for application-level analysis. Matching the test conditions to the design, understanding the thermal path, and validating operation under real circuit conditions are essential steps before incorporating this MOSFET into an industrial power system.