Access Official Technical PDF

Share Summary:LinkedInEmail

In embedded electronics, the voltage regulator must fit the available supply range, load demand and board constraints while maintaining a stable output. The S-1333 voltage regulator is a CMOS positive regulator designed for applications requiring low current consumption, low dropout voltage and high ripple rejection. Its specifications and selectable control functions make it important to assess not only the target voltage, but also operating conditions, shutdown behavior, thermal limits and external capacitors.

S-1333 voltage regulator operating range and performance

The S-1333 accepts an input voltage from 1.5 V to 5.5 V. Output voltage options span 1.0 V to 3.5 V in 0.05 V increments. Output accuracy is specified as ±1.0% for set voltages from 1.5 V upward, and ±15 mV for outputs below 1.5 V. These tolerances apply under the conditions stated in the device specifications; changes in input voltage, load or temperature can affect the actual output.

Typical operating current is 25 μA, with a maximum specified value of 38 μA. In power-off mode, typical current consumption is 0.1 μA and the maximum is 1.0 μA. This low-current behavior can be relevant in battery-powered equipment or other designs where a regulator remains connected to its supply during periods of inactivity.

The series can provide up to 300 mA for output settings of at least 1.3 V when the input is at least 1.0 V above the set output. The specified available current is lower for some output settings below 1.3 V. In all cases, designers must also check package power dissipation: a nominal current capability does not remove the thermal constraints imposed by the input-to-output voltage difference, load and mounting conditions.

Dropout, ripple rejection and load behavior

As a low-dropout regulator, the S-1333 uses a low-on-resistance P-channel MOSFET as its output transistor. Dropout voltage depends on output setting and load current. For example, the typical dropout voltage for the 2.8 V output product is 160 mV at 100 mA. The data sheet gives separate values across output-voltage ranges, so a design should use the relevant specification rather than assume one dropout figure applies to every variant.

Ripple rejection is specified at 1 kHz and varies with output voltage: typical values are 75 dB for output settings from 1.0 V through 1.6 V, 70 dB above 1.6 V through 2.85 V, and 65 dB above 2.85 V through 3.5 V. These are condition-specific figures, not a guarantee of equal rejection at every frequency or load. Review the characteristic data when supply ripple is a concern.

Line regulation describes how output changes as input voltage changes while load remains fixed; load regulation describes output change as load varies while input remains fixed. Both matter when validating a rail that supplies electronics with changing operating states. The S-1333 specifications include load-regulation measurements at different current ranges, which helps engineers compare expected behavior with the application’s load profile.

Choose shutdown and output-discharge behavior

All S-1333 variants use an active-high ON/OFF pin. Driving it high enables regulation; driving it low stops the internal circuit and turns off the output transistor. The four product types differ in two details: whether they include an output discharge shunt and whether the ON/OFF pin has an internal pull-down resistor.

  • Type A: discharge shunt available; ON/OFF pull-down resistor available.
  • Type B: discharge shunt available; ON/OFF pull-down resistor unavailable.
  • Type C: discharge shunt unavailable; ON/OFF pull-down resistor available.
  • Type D: neither function available.

The discharge shunt in A and B helps discharge the output capacitor after shutdown, bringing the output toward ground more rapidly. C and D lack this shunt; the output instead reaches ground through internal divider resistors. For B and D, the ON/OFF input must not be left floating; if the control pin is unused, connect it to VIN. A and C have an internal pull-down, but connecting the pin to VIN during operation causes current to flow through that resistor.

Capacitors, layout and thermal checks

The recommended input capacitor (CIN) and output capacitor (CL) are each at least 1.0 μF. The output capacitor is required for phase compensation and stable operation. Ceramic capacitors can be used, and the specified capacitance should be maintained across the application’s temperature conditions. The selected capacitance also affects output overshoot, undershoot and transient response, so the minimum value alone does not establish performance in every circuit.

Place the input and output capacitors close to their respective regulator pins, and keep VIN, VOUT and ground wiring impedance low. Confirm stability and output behavior using the actual components, board layout, input source and load. A high-impedance supply combined with insufficient input capacitance can contribute to oscillation; inadequate output capacitance can worsen supply and load-fluctuation behavior.

The device includes overcurrent protection and thermal shutdown. Short-circuit current is typically about 50 mA, but the overcurrent circuit is not a substitute for thermal protection or a reason to leave the output shorted. Thermal shutdown typically stops regulation at a junction temperature of 150°C and restarts it at 120°C. Repeated shutdown and restart can produce a pulse-like output if excessive heating continues. Reduce the conditions causing internal power loss and check that the application remains within the package’s power-dissipation limits.

Package selection and design validation

The series is offered in SOT-23-5, HSNT-4 (1010) and HSNT-4 (0808) packages. Selection depends on board requirements and assembly considerations, but package thermal capability must be evaluated alongside output current. For the HSNT packages, the backside heat sink should be connected to the board as specified; it must not be used as an electrical electrode. Confirm the pinout and mounting guidance for the chosen package.

Before committing a design, match the output voltage and product type to the required rail and shutdown sequence, verify input headroom across operating conditions, calculate package dissipation, and test capacitor behavior on the actual board. The S-1333 provides a compact set of regulation and control options, but successful integration depends on observing its electrical limits and validating stability, thermal performance and output behavior in the intended application.

Access Official Technical PDF

About The Author