A transient voltage suppressor (TVS) can help protect power electronics from short-duration voltage disturbances. The Sensitron 704-15K36T is a unidirectional device intended primarily for avionics equipment, with a stated application focus on 28V power supply protection and design for MIL-STD-704. Its ratings provide useful selection data, but engineers must compare them with the actual supply, transient profile, and circuit conditions rather than treating a single headline rating as a complete protection guarantee.
What the 704-15K36T is designed to do
The 704-15K36T is a 15kW transient voltage suppressor assembly. The datasheet identifies it as an equivalent to industry-standard part number 704-15K36T and describes typical operation with a minimum transient source impedance of 0.25 ohms. That source-impedance condition matters: the device’s behavior in an installed circuit depends on the transient source as well as the suppressor and the protected load.
As a unidirectional device, it has a defined polarity. The cathode terminal is marked with a dot, so installation orientation should be verified against the circuit design. The datasheet also states that electrical characteristics are tested at 25°C and “both polarities”; this test note does not change the specified unidirectional designation or remove the need to observe the device’s marked polarity in an application.
Reading the key transient voltage suppressor ratings
Several voltage and current values describe different operating points. They should be read together when assessing whether the device fits a 28V supply and its expected transients:
- Reverse stand-off voltage (VWM): 31.5V. The datasheet says the selected stand-off voltage should be equal to or greater than the DC or continuous peak operating voltage. Confirm that the maximum normal voltage in the application does not exceed this value.
- Breakdown voltage (V(BR)): 36V minimum at 10mA. This is the stated minimum breakdown point under the listed test condition. It is distinct from both the stand-off voltage and the clamping voltage.
- Clamping voltage (VC): 51V maximum at IPP. The listed clamping value applies at the specified maximum peak pulse current of 300A. It indicates the device’s maximum stated clamp under that condition, not a fixed voltage for every transient.
- Maximum peak pulse current (IPP): 300A. The datasheet references Figure 2 for this value, so engineers should consult the complete, current datasheet for the applicable waveform and conditions before final design.
These ratings help frame the protection trade-off. The supply’s normal operating voltage must remain within the chosen stand-off rating, while the protected circuit must be able to tolerate the voltage that may appear at the stated clamping condition. The equipment’s transient environment and the TVS’s actual installation conditions are therefore part of the selection decision.
Power, timing, and operating limits
The datasheet lists peak pulse power dissipation of 15,000W at 1ms and a steady-state power dissipation rating of 10W. These are different limits: the peak pulse rating concerns a specified transient condition, while the steady-state value applies to continuous dissipation. Neither rating should be interpreted without its stated conditions or as permission to exceed other maximum ratings.
The listed typical clamping time from 0V to V(BR) is less than 1 × 10-12 seconds. The datasheet also specifies a maximum duty cycle of 0.01% and a forward surge current of 300A for 1/120 second at 25°C. These figures describe distinct conditions and should not be combined into an assumed capability for arbitrary pulse shapes or repetition rates.
The operating and storage temperature range is -65°C to +150°C. Temperature, pulse repetition, and thermal paths should be considered alongside the electrical ratings when reviewing the design. The part’s listed weight is 38 grams, and its molded case has silver-plated brass terminals; mounting position is specified as unrestricted.
Practical integration checks
Before using the 704-15K36T in an avionics power circuit, engineers and system integrators should check the complete application rather than relying only on its 15kW designation. A practical review includes:
- Confirming the normal DC and continuous peak supply voltage against the 31.5V reverse stand-off rating.
- Comparing expected transient current and waveform with the conditions associated with the 300A peak pulse rating.
- Checking that the downstream equipment can tolerate the stated clamping voltage under the relevant test condition.
- Accounting for the datasheet’s typical minimum transient source impedance of 0.25 ohms when evaluating the source and protection network.
- Verifying polarity, terminal identification, mounting, temperature range, and duty cycle in the intended installation.
The datasheet notes that special voltages are available from the factory. It also advises purchasers to contact Sensitron for the latest datasheet version before ordering, since specifications and dimensions may change. Engineers should use the current documentation and verify suitability against the applicable system requirements; the device description alone does not establish compliance with every MIL-STD-704 condition or a complete system-level protection design.
Conclusion: match the device to the system
The 704-15K36T offers a defined set of ratings for transient protection in 28V avionics applications, including a 31.5V stand-off voltage, 36V minimum breakdown voltage, and 51V maximum clamping voltage at the stated peak current. For reliable circuit selection, compare these values with normal supply limits, transient characteristics, source impedance, and the protected load’s voltage tolerance. Careful attention to polarity, pulse conditions, and the latest manufacturer documentation turns component ratings into a useful part of a system-level protection assessment.