Access Official Technical PDF

Share Summary:LinkedInEmail

The FQP13N50C MOSFET and its full-pack counterpart, the FQPF13N50C, are 500 V N-channel enhancement-mode power devices designed for power-conversion circuits. Their stated headline ratings—500 V drain-source voltage, 13 A continuous drain current under specified conditions, and a maximum on-resistance of 480 mΩ—make them candidates for applications such as switched-mode power supplies, active power factor correction, and half-bridge electronic lamp ballasts. Correct selection depends on more than those headline numbers: operating conditions, switching behavior, package thermal limits, and transient stresses all matter.

FQP13N50C MOSFET ratings and intended applications

The devices use a planar stripe DMOS structure. The manufacturer describes the technology as tailored to reduce on-state resistance, support switching performance, and withstand high-energy pulses in avalanche and commutation modes. The data sheet identifies the FQP13N50C and FQPF13N50C as suitable for high-efficiency switched-mode power supplies, active power factor correction stages, and half-bridge electronic lamp ballasts.

The 500 V drain-source breakdown rating is specified with the gate-source voltage at 0 V and a drain current of 250 µA. It is a component limit, not a recommendation to operate a circuit continuously at that voltage. Design teams need to evaluate the circuit’s normal voltage, switching transients, and operating conditions against the relevant device limits.

The maximum continuous drain current is listed as 13 A at a case temperature of 25°C. At a case temperature of 100°C, the listed continuous current falls to 8 A. The 52 A pulsed rating is subject to pulse-width limitations imposed by maximum junction temperature, so it should not be treated as a general continuous or unrestricted pulse-current capability.

On-resistance, gate charge, and switching behavior

On-resistance affects conduction losses while the MOSFET is on. The data sheet specifies a maximum static drain-source on-resistance of 0.48 Ω, with a typical value of 0.39 Ω, at a gate-source voltage of 10 V and drain current of 6.5 A. These test conditions are important: the figure should not be assumed to apply at every gate voltage, current, or junction temperature.

For switching designs, the gate-charge and capacitance figures help characterize the load seen by the gate driver. Total gate charge is 43 nC typical and 56 nC maximum under the stated test conditions of 400 V drain-source voltage, 13 A drain current, and 10 V gate-source voltage. Typical gate-source charge is 7.5 nC, while typical gate-drain charge is 18.5 nC. Typical input capacitance is 1,580 pF, output capacitance is 180 pF, and reverse-transfer capacitance is 20 pF.

The specified resistive-switching test gives typical turn-on delay, rise, turn-off delay, and fall times of 25 ns, 100 ns, 130 ns, and 100 ns, respectively. These are test results under defined conditions, not guaranteed timing for every circuit. Actual switching behavior depends on the external gate-drive circuit and application conditions. The data sheet also lists a 410 ns typical body-diode reverse-recovery time and 4.5 µC typical reverse-recovery charge under its specified test setup. These diode characteristics are relevant when evaluating commutation behavior in circuits that use the body diode.

Thermal limits and package selection

The two part numbers share key electrical ratings but use different packages: the FQP13N50C comes in a TO-220 package, while the FQPF13N50C uses a TO-220F full-pack package. Their power dissipation and junction-to-case thermal resistance ratings differ, which affects thermal design.

  • FQP13N50C: Maximum power dissipation is 195 W at a 25°C case temperature, with maximum junction-to-case thermal resistance of 0.64°C/W.
  • FQPF13N50C: Maximum power dissipation is 48 W at a 25°C case temperature, with maximum junction-to-case thermal resistance of 2.58°C/W.

These power figures are specified with the case held at the stated temperature; they do not represent allowable dissipation in an arbitrary installation. The data sheet gives a maximum junction-to-ambient thermal resistance of 62.5°C/W for both versions and, for the FQP13N50C, a typical case-to-sink thermal resistance of 0.5°C/W. In practice, engineers should assess the complete thermal path and use the relevant package-specific limits alongside the device’s operating conditions.

The operating and storage temperature range is -55°C to +150°C. The data sheet also provides transient thermal response curves and safe operating area plots for each package. These are useful when checking pulsed operation and thermal behavior over time; the safe operating area must be read for the applicable package, pulse duration, and conditions shown.

Avalanche capability and design checks

Both devices are identified as 100% avalanche tested. The data sheet specifies a single-pulsed avalanche energy of 860 mJ under a defined test setup, including a 6 mH inductor, 13 A avalanche current, 50 V supply, and 25°C starting junction temperature. Repetitive avalanche energy is listed as 19.5 mJ, and avalanche current as 13 A. These values describe specified test conditions; they do not remove the need to assess energy, repetition, temperature, and circuit behavior in the intended application.

Before choosing either device, engineers should verify the gate-drive voltage, expected current and voltage waveforms, switching losses, transient stresses, and thermal conditions. The maximum gate-source rating is ±30 V, while the on-resistance specification uses a 10 V gate drive. Confirming the operating point against the data sheet’s electrical characteristics, safe operating area, and package-specific thermal data helps avoid relying on a headline rating outside its stated conditions.

Conclusion

The FQP13N50C and FQPF13N50C combine a 500 V drain-source rating with defined switching, gate-charge, avalanche, and diode characteristics for power-conversion applications. The central selection distinction is the package: the TO-220 FQP version and TO-220F FQPF version have different power-dissipation and junction-to-case thermal ratings. Treat current and voltage figures as condition-dependent limits, and validate switching and thermal performance for the actual circuit before finalizing a design.

Access Official Technical PDF

About The Author