Livestock feed additives must balance practical handling, functional value, and cost. One approach examined in agricultural research is using flax and hemp shives—the woody residue left after processing plant fibers—as a carrier for a biologically active preparation. The work assessed whether these cellulose-containing materials could adsorb Floravit® vapors and then be incorporated into compound feed.
Why consider plant-processing residues for livestock feed additives?
Feed contamination by mycotoxins and other undesirable substances can affect animal health and productivity. Enterosorbents are used in feed strategies to bind harmful compounds in the digestive tract; the research describes this approach as a practical alternative to treating contaminated feed with chemical reagents or heat.
Conventional adsorbents such as activated carbon can be costly. By contrast, flax and hemp shives are renewable by-products of plant processing. The paper identifies their comparatively low cost and availability as reasons to assess them as a potential sorbent and feed ingredient. It also notes that shives can be used without prior chemical treatment or steaming.
The study focused on a related but distinct application: loading shives with Floravit®, a preparation described by the authors as a broad-spectrum bioregulator used to support nonspecific resistance. Rather than applying the preparation separately, the proposed method was to expose the plant material to Floravit vapors and then add the treated carrier directly to compound feed.
Assessing adsorption capacity of flax and hemp shives
For this carrier concept to be useful, the plant material must take up the preparation effectively and within a practical period. The researchers therefore evaluated the sorption of Floravit vapors by flax shives from the Antey variety and hemp shives from the YUSO-31 variety.
The reported results indicate that sufficient uptake for applying the biologically active preparation was achieved after one to two hours in an atmosphere saturated with Floravit vapors. The authors also observed that the sorption process followed a mechanism similar to the adsorption of water vapor. This comparison describes the behavior of the materials; it does not establish that water vapor and Floravit have identical properties or performance.
Under the conditions examined, hemp shives had a sorption capacity 33% higher than flax shives. This finding suggests that the choice of carrier material can influence how much vapor is taken up. However, the result applies to the specific plant varieties studied and should not be treated as a universal value for all flax or hemp residues.
Potential production and handling advantages
The proposed process has a straightforward manufacturing rationale. After exposure to Floravit vapors, the treated shives could be packed and transported without a subsequent drying step, according to the paper. Avoiding additional drying may reduce process energy requirements, while a ready-to-pack carrier could simplify handling between preparation and feed production.
For feed manufacturers and integrators evaluating the concept, the study points to several considerations:
- Feedstock selection: Shive type and source may affect adsorption capacity, so the materials should be assessed rather than assumed interchangeable.
- Exposure time: The reported one-to-two-hour period provides an initial process reference for the varieties studied.
- Integration: The intended use is to incorporate the preparation-bearing carrier into compound feed.
- Economics: The authors identify low-cost plant residues as a potential advantage, but the paper does not provide a full-scale cost analysis.
What the findings do—and do not—establish
The work supports the possibility of using flax and hemp shives as a cellulose-based carrier for Floravit. It also provides a comparative result for the tested materials and a preliminary indication of the exposure time needed for vapor sorption. These are useful starting points for process development, particularly where plant-processing residues are locally available.
The findings do not, on their own, demonstrate the effectiveness of the treated shives in animal feeding trials, establish an optimal inclusion rate, or quantify toxin-binding performance in the digestive tract. Nor does the paper report a complete assessment of storage stability, consistency between residue batches, or commercial-scale production. Those questions require further evaluation before the approach can be specified for routine feed manufacturing.
Practical implications for feed operations
For operations teams, the main takeaway is that agricultural by-products may have a role beyond disposal or low-value use: they can be investigated as functional carriers for feed preparations. The reported higher adsorption capacity of hemp shives may guide material selection, while the short vapor-exposure period and omission of a drying stage offer potential process advantages.
Before adopting this approach, feed producers should verify the properties of their available shive supply and determine whether the treatment process delivers consistent, suitable material for their intended feed application. The study establishes a promising technical possibility, not a finished commercial specification. Careful validation of carrier quality, process repeatability, and feeding outcomes is the practical next step.