Access Official Technical PDF

Share Summary:LinkedInEmail

The FX2LP USB microcontroller combines a USB 2.0 transceiver, serial interface engine (SIE), enhanced 8051 processor and programmable peripheral interfaces in a single device. For industrial automation engineers and system designers, that integration offers a way to connect a USB host to external processors, programmable logic or parallel data sources without building the USB interface from separate components.

Its design is centered on moving data between USB and an external interface. The SIE handles much of the USB protocol in hardware, while the 8051 runs application firmware and configures the device. The general programmable interface (GPIF) and slave FIFO modes provide different approaches to connecting that USB link to external hardware.

What the FX2LP USB microcontroller integrates

The FX2LP supports USB 2.0 full-speed signaling at 12 Mbps and high-speed signaling at 480 Mbps; it does not support low-speed USB. The device datasheet describes data-transfer rates of more than 53 Mbytes per second, while noting that this is within the maximum bandwidth allowed by USB 2.0. Actual system performance depends on the complete design and data path.

The integrated enhanced 8051 can operate at 12, 24 or 48 MHz, with four clocks per instruction cycle. It includes two USARTs, three counter/timers and an expanded interrupt system. A 24-MHz external crystal and on-chip PLL provide the clocking arrangement described for the USB transceiver and processor.

Combining the SIE and transceiver with the processor can reduce the need for separate USB interface components. The SIE also takes care of much of the USB 1.1 and 2.0 protocol processing, leaving the 8051 available for device-specific firmware tasks. The chip has 16 KB of on-chip code/data RAM, and firmware can be loaded through USB, from an I2C EEPROM, or from external memory in the 128-pin package.

GPIF and slave FIFO: two interface strategies

A key design choice is how the FX2LP will exchange data with external hardware. Its GPIF mode uses an internally controlled, programmable state machine. In slave FIFO mode, external logic controls transfers through FIFO signals. Both modes use endpoint memory as part of the data path, but they suit different control arrangements.

Using GPIF for programmable parallel transfers

The GPIF is an 8-bit or 16-bit parallel interface that can generate data and control signals for an external device. Firmware configures waveform descriptors and registers to define the sequence of operations. Ready inputs can be checked as the sequence runs, while control outputs and address lines support interaction with the connected hardware.

This approach is useful when the FX2LP should manage transfer timing and sequencing. The datasheet lists interfaces such as ATA, printer parallel port and UTOPIA as examples, and describes connections to ASICs, DSPs and other parallel interfaces. Signal availability depends on the package: larger packages expose more GPIF control, ready and address signals than the 56-pin versions.

Using slave FIFO mode with external control

In slave FIFO mode, external logic drives signals such as SLRD, SLWR, SLOE and PKTEND to control reads and writes. The interface can use an internally derived or external clock, with an IFCLK input frequency of up to 48 MHz. It supports synchronous operation, where transfers are clocked, and asynchronous operation, where read and write signals act as strobes.

This arrangement can suit a design in which another device already controls the data-transfer timing. The bus can be configured for 8-bit or 16-bit transfers. Engineers should check package pin availability, clocking requirements and the relevant signal timing specifications when selecting this mode.

Endpoint buffering and USB data flow

The FX2LP endpoint architecture provides buffers for USB traffic and the external interface. Endpoint zero supports control transfers, while endpoint one can be configured for bulk or interrupt traffic. Endpoints 2, 4, 6 and 8 support bulk, interrupt or isochronous transfers, with buffering options that include double, triple or quad buffering for selected endpoints.

Buffering lets one part of the device exchange data with USB while other buffer blocks are available to the 8051 or I/O interface. The datasheet describes eight physically distinct 512-byte RAM blocks that can be assigned between the USB SIE and I/O domains. Because the same memory serves both sides, data does not need to be copied between separate USB and slave FIFO buffers.

Endpoint configuration and packet size depend on operating speed and transfer type. For example, high-speed bulk endpoints can use 512-byte packets, while full-speed bulk packets use 64 bytes. These details matter when firmware, host software and external logic must agree on how data is divided and handled.

Power, boot and package choices

The FX2LP operates at 3.3 V and has 5-V-tolerant inputs. Its low-power design supports bus-powered and battery-powered applications. Within the device family, the CY7C68014A and CY7C68016A versions have a typical suspend current of 100 μA, compared with 300 μA for the CY7C68013A and CY7C68015A versions, as specified in the datasheet. Package and GPIO options also vary across the family.

At startup, the device checks the I2C interface for an EEPROM. Depending on its contents, the EEPROM can supply identification and configuration values or load firmware into internal RAM. Without an EEPROM, the FX2LP enumerates using its internally stored descriptors. Firmware can also use ReNumeration: the device first enumerates, receives firmware and USB descriptors over USB, and then reconnects as the configured device.

Design considerations for integration

Before choosing the FX2LP, teams should map interface needs to the available package and operating mode. In particular, review:

  • Whether GPIF-master control or externally controlled slave FIFO transfers better match the connected hardware.
  • The required bus width, clock source, endpoint types and buffering configuration.
  • Available GPIO and GPIF signals for the selected package.
  • Firmware boot requirements, including USB download or I2C EEPROM loading.
  • Power needs, including the distinction between the lower-suspend-current and standard variants.

Designers migrating from the earlier FX2 can benefit from pin, package and broad firmware compatibility, but should still review memory allocation and bill-of-materials changes. The FX2LP has more internal RAM, and the product documentation notes exceptions that require attention during migration.

Conclusion

The FX2LP is an embedded USB controller built to bridge high-speed USB and parallel data interfaces. Its integrated 8051, configurable endpoint memory, GPIF and slave FIFO modes give designers flexibility in deciding where transfer control belongs. A successful implementation depends on matching the interface mode, package, firmware boot strategy and endpoint configuration to the surrounding system—not simply selecting the device based on USB speed alone.

Access Official Technical PDF

About The Author