A USB-UART bridge controller can provide a practical link between a USB host and equipment built around an established UART interface. The CY7C65213 and CY7C65213A combine USB 2.0 Full-Speed connectivity with a configurable, single-channel UART, helping designers add USB access to embedded systems, industrial equipment and test-and-measurement devices. Selecting and integrating the device involves more than connecting transmit and receive lines: interface levels, flow control, USB power behavior and model-specific capabilities all matter.
How the CY7C65213 family bridges USB and UART
The controller integrates a USB Full-Speed transceiver, UART communication block, internal regulator, clock oscillator and 512 bytes of flash for configuration data. Its USB interface is certified to USB 2.0 Full-Speed, or 12 Mbps, and includes termination resistors. On the host, Cypress virtual COM port drivers allow compatible applications to communicate through a COM port; the device also supports USB CDC operation.
The UART is asynchronous and supports data rates from 300 baud to 3 Mbaud. Designers can configure 7- or 8-bit data, one or two stop bits, and no parity, odd, even, mark or space parity. Separate 256-byte transmit and receive buffers support full-duplex communication. The controller can report parity, framing and overrun errors, and it supports a UART break signal.
The bridge handles USB-to-UART conversion; it does not by itself create RS-232 or RS-485 electrical signaling. Those interfaces require an appropriate external transceiver to translate between the UART’s logic-level signals and the relevant physical layer.
Choose the model for the serial interface
The key distinction between the two family members is RS-485 support. CY7C65213 supports UART connections to RS-232 or RS-422 transceivers. CY7C65213A supports those options and RS-485. For a half-duplex RS-485 design, the documentation describes using a GPIO signal, such as TXDEN, to control an external transceiver’s transmit enable. That signal’s configuration and timing should be checked against the transceiver and application requirements.
Both devices provide hardware flow-control signals, including CTS/RTS and DSR/DTR, alongside UART data signals. CTS can pause or resume transmission. Receive-side RTS flow control uses buffer thresholds: the device de-asserts RTS when the receive buffer reaches a 93% watermark and asserts it again after the application consumes data down to the 75% watermark. This helps coordinate data flow between connected devices, but the system must wire and configure the relevant signals appropriately.
Configure GPIO and USB identity for the application
Eight GPIO pins can be assigned functions through the Windows configuration utility. Options include static high or low outputs, transmit and receive activity indicators, a suspend-status output, USB bus detection, charger-detection outputs and power control. A POWER# configuration can control external logic so that it remains within the stated USB current limits before enumeration and during suspend.
The 512-byte internal flash stores settings such as USB vendor and product IDs, manufacturer and product strings, serial number, power mode, maximum current declaration, UART format and GPIO assignments. The utility can save or load configurations in text or XML formats. A unique serial-number feature can help keep a device’s COM port assignment fixed when it is reconnected, an operational consideration for systems that associate software settings with a particular serial device.
Configuration should match the finished hardware and host behavior. For example, the selected USB interface class, declared power mode and current draw should reflect the actual design. UART baud rate and framing must also agree with the connected equipment; mismatches can lead to communication errors even when USB enumeration succeeds.
Plan power, suspend and charging behavior
The controller supports both bus-powered and self-powered designs, as well as USB suspend and resume behavior. In a bus-powered system, the documented limits include no more than 100 mA before USB enumeration, no more than 2.5 mA during suspend, and no more than 500 mA drawn from the USB host. A design that needs more than 100 mA during normal operation must manage external loads so the pre-enumeration and suspend limits are respected. Its USB configuration descriptor should declare the appropriate power mode and maximum current.
For self-powered designs, the external supply powers VCCIO, while USB VBUS is used to detect the host connection. The reference design uses VBUS to control reset, allowing the USB data-line pull-up to be removed when the host is absent. The device also provides a SLEEP# indication for USB suspend, and the RI# input can be configured to request remote wakeup when the host has enabled that feature.
Battery charger detection complies with USB Battery Charging Specification Revision 1.2 for peripheral detection only. Configured GPIO outputs can indicate charger type. This feature should not be confused with a complete battery-charging function: the source describes the controller detecting and indicating the port type, while charging is handled by the surrounding system.
Check electrical and implementation requirements
The documented operating range includes an industrial temperature range of −40 °C to 85 °C. VCC is specified from 3.15 V to 5.25 V, while VCCIO supports 1.71 V to 5.50 V. The VCCD pin is associated with the internal regulator and is not intended to power external devices; its connection or decoupling depends on the VCCIO voltage. Follow the device pin and power-configuration requirements during schematic and layout review.
Available packages include a 28-pin SSOP and a 32-pin QFN. The family also has documented drivers and software libraries for several operating systems, including Windows, Linux, macOS, Windows CE and Android. Confirm that the required driver model and operating-system version fit the target host environment before committing to an interface design.
Conclusion: Treat the bridge as part of the system
The CY7C65213 family offers a configurable route from USB to UART for equipment that needs a host connection without replacing its serial interface. The practical design choices are the RS-485-capable CY7C65213A variant where needed, the external transceiver for the physical layer, suitable UART flow control, accurate USB descriptors and compliant power management. Reviewing these elements together helps engineers integrate the bridge into embedded and industrial systems with fewer surprises during host connection and operation.