GaN DC-DC converters offer a route to higher efficiency and power density in modular photovoltaic (PV) systems, where each solar module has its own power converter and maximum power point tracking (MPPT). This arrangement can help modules operate independently when their electrical outputs differ, but it also increases the number of converters in a system. Improving each converter’s performance and reducing its size are therefore important design goals.
A research design for parallel-type modular PV applications combines gallium nitride (GaN) switches with an isolated resonant converter. Its reported 300-watt prototype reached a peak efficiency of 98.9% and a California Energy Commission (CEC) weighted efficiency of 98.7% at nominal input voltage. A further 1-MHz design reduced volume by more than 70% relative to a 140-kHz version, while CEC efficiency fell by 0.8 percentage points at nominal input voltage.
Why modular PV converters need both efficiency and density
PV module voltage and available power vary with conditions such as irradiance, temperature and partial shading. A modular architecture places a converter at each module, allowing module-level MPPT rather than requiring an entire string to operate around the output of its weakest module. In a parallel-type arrangement, each converter raises the module’s relatively low DC voltage to a higher-voltage bus.
The tradeoff is that more power-electronic units are required. In a system that processes energy through both a module-level DC-DC converter and a string inverter, losses from the two stages accumulate. More converters also mean more components and enclosure or potting material. Higher conversion efficiency can limit energy losses, while greater power density creates opportunities to reduce converter size and associated material requirements.
How GaN supports high-efficiency DC-DC conversion
Conventional silicon power devices are mature, but their scope for further improvement in converter efficiency and power density is limited. Wide bandgap semiconductors such as GaN provide different device characteristics, including low on-state resistance, small junction capacitance and high switching speed. These properties can reduce conduction and switching losses and support operation at higher switching frequencies.
Device characteristics alone do not guarantee a better converter. The switching method, circuit topology, layout and magnetic components all affect system-level results. The design therefore evaluated GaN devices under both hard-switching and soft-switching conditions, examining behavior during steady operation and switching transitions at different power levels. This matters because a device’s performance in a circuit depends not just on its steady-state current handling, but also on how it turns on and off.
Resonant topology combines isolation and wide-range regulation
The proposed isolated converter builds on a series resonant converter (SRC) and adds an active-boost-rectifier on the secondary side. The rectifier combines functions associated with a boost circuit and a voltage-doubler rectifier. With a double-pulse duty-cycle modulation method, the secondary-side switches provide synchronous rectification while also enabling voltage boost.
This configuration addresses a common design challenge: achieving high voltage gain and a wide input-regulation range without adding more switches. The converter operates at a fixed switching frequency and retains the advantages of resonant conversion while extending voltage gain beyond that of a conventional SRC.
Soft switching reduces the overlap of voltage and current during switching transitions. In this design, primary-side switches achieve zero-voltage switching (ZVS), while secondary-side switches achieve zero-current switching (ZCS), across the stated input-voltage and output-power operating conditions. These conditions are intended to reduce switching-related losses and support high efficiency. GaN devices are used on both the primary and secondary sides.
What changes when switching frequency reaches 1 MHz?
Increasing switching frequency can make it possible to reduce the size of magnetic components, supporting a more compact power stage. But higher frequency also increases the importance of AC effects, parasitic elements and physical layout. The 1-MHz design used finite element method (FEM) simulations to optimize the magnetic components and printed circuit board (PCB) structure.
Comparing the 1-MHz design with the 140-kHz version illustrates the practical tradeoff: volume decreased by more than 70%, while CEC efficiency at nominal input voltage was 0.8 percentage points lower. These results describe the specific designs and operating condition evaluated; they are not a general guarantee that increasing frequency will produce the same outcome in other converters.
Layout parasitics are part of the resonant design
At MHz switching frequencies, PCB layout is not merely a packaging concern. Parasitic inductance and capacitance can change resonant behavior and switching transitions, so they need to be included in analysis and design.
- Primary-side parasitic inductance: If the power loops for the positive and negative half cycles have unequal parasitic inductances, resonant current can become unbalanced between the two half cycles. Symmetry in the layout helps limit this source of imbalance.
- Inductance reflected to the secondary: Parasitic inductances from the primary side, when reflected to the secondary, should be considered when selecting the resonant inductance.
- Secondary-side parasitic capacitance: Capacitance can affect ZVS transitions and increase the magnetizing current required. At MHz operation, dead time can occupy a substantial portion of the switching period, making its effect on resonant-network design important.
These interactions show why a frequency increase cannot be treated as a simple adjustment to the switching control. The resonant tank, transformer, PCB power loops and dead-time settings need to be considered together.
Practical implications for converter development
For engineers and system integrators evaluating modular PV power conversion, the design demonstrates how device selection, topology and layout choices can work as a coordinated system. GaN switches create opportunities for lower losses and higher switching frequency; resonant operation provides soft-switching transitions; and the active-boost-rectifier supports high gain and wide-range regulation.
The reported prototypes also highlight the cost of pursuing higher power density: a substantial volume reduction came with a modest efficiency decrease in the 1-MHz comparison, and parasitic effects required detailed attention. Converter selection and optimization should therefore consider the full operating range, thermal and electrical design requirements, layout, and the system-level consequences of adding a conversion stage.
In short, GaN DC-DC converters can help address efficiency and size constraints in modular PV architectures, but the benefits depend on careful implementation. For practical designs, soft-switching behavior, magnetic optimization and PCB parasitics are as important as the semiconductor technology itself.