Access Official Technical PDF

Share Summary:LinkedInEmail

The SR2MOD02 SR2MOD03 modem family provides 2G/3G cellular connectivity for specific Schneider Electric control platforms. SR2MOD02 is intended for Zelio Logic smart relays, while SR2MOD03 supports M221, M241, and M251 Logic Controllers. For engineers and system integrators, successful deployment depends on more than connecting a cellular antenna: controller compatibility, power quality, serial-port settings, SIM status, and network coverage all need to be checked as part of commissioning.

These devices support GSM/EDGE and UMTS/HSPA networks, with supported bands varying by modem manufacturing date. The product documentation states that units manufactured from date code 1630 onward support six UMTS bands. Because network availability and product details can change, confirm the characteristics of the specific unit and the locally available cellular service before designing an installation.

Where the SR2MOD02 and SR2MOD03 fit

The modems connect a supported controller to cellular networks using a SIM card and an RS-232 serial link. Their cellular functions include voice and packet-switched data, as well as SMS capabilities. The documented radio technologies include quad-band GSM at 850, 900, 1800, and 1900 MHz, EDGE, and UMTS/HSPA across supported bands. The exact 3G band support depends on the unit’s manufacturing date.

Integration planning should begin with the controller reference and intended communications method. The modem’s RS-232 port is the connection between the cellular module and the controller or another data terminal equipment (DTE) device. A supplied 15-pin-to-9-pin adapter cable supports connection to a compatible serial cable. Check the pinout and the controller’s serial interface requirements rather than assuming that every RS-232 cable is wired identically.

Power, antenna, and installation requirements

Use an external, regulated DC supply rated from 7.2 to 32 Vdc. The equipment must not be connected directly to line voltage; the documentation specifies a minimum PELV-rated supply. If the input falls below 7.2 Vdc, GSM/UMTS/HSPA communication may not operate correctly. Cellular data transmission can also involve higher current draw than the modem’s attached state, so the supply should be selected with the documented operating conditions in mind.

The antenna connects through a 50-ohm female SMA connector. The supplied magnetic antenna is designed for vertical placement on a metallic support. Follow the manufacturer’s installation instructions, including the specified 20.3 cm minimum separation from people, and do not substitute or share the antenna with another device. Install the modem only in a non-hazardous location and within its stated environmental limits.

Mounting options include a 35 mm DIN rail clip or two surface-mount brackets. Before wiring, isolate power from the equipment and connected devices as required by the applicable hardware instructions. Insert the SIM card with the modem turned off, secure its cover, attach the antenna and serial connection, and then connect the external supply. The modem has an IP31 enclosure rating, so enclosure and placement decisions should account for the actual installation environment.

Commissioning the RS-232 and cellular connection

The RS-232 interface carries data and can also support hardware-handshake signals, including RTS, CTS, DTR, DSR, DCD, and RI. The modem can operate in a three-wire arrangement using TX, RX, and ground, where appropriate for the connected equipment. The guide also describes auto-baud detection for a defined set of serial speeds; do not assume it will reliably detect rates outside that supported set.

Serial settings differ between the two references. For SR2MOD02, the documented settings are 115200 baud, 7 data bits, even parity, one stop bit, hardware flow control enabled, and DSR set to 1. For SR2MOD03, the settings are 19200 baud, 8 data bits, no parity, one stop bit, hardware flow control disabled, and DSR off. Both configurations specify disabled AT-command echo. Use the settings for the modem reference in the installation, then verify communication before proceeding.

A basic PC-based check is to connect through an RS-232 port and send AT followed by a carriage return. An OK response indicates that the serial link is responding. If there is no response, check the cable and port configuration first. The modem’s AT command set can then help separate serial, SIM, and cellular-network issues:

  • AT+CPIN? checks SIM PIN status. A ready response indicates that the PIN is accepted; other responses can indicate a missing or unrecognized SIM, a PIN still required, or a PUK requirement.
  • AT+CSQ reports received signal strength and signal quality. Interpret these values in the context of the 2G or 3G network and the current radio conditions.
  • AT+CREG? reports network registration status, including whether the modem is searching, registered with a local operator, or registered while roaming.

The modem’s side LED provides another useful commissioning indicator. Its patterns distinguish states such as no power or reset, readiness without network connection, network search, registration on 2G or 3G, and data transmission. Use the LED alongside AT-command responses; neither should be treated in isolation when diagnosing a connection.

Diagnosing common connection problems

If the modem responds to AT commands but does not register, verify that a valid SIM is installed, enter its PIN if required, check antenna attachment, and inspect received signal strength. A low signal reading can prevent a call or data connection, while a registration response indicating network search points to a different condition than an accepted local or roaming registration. Also confirm that the selected network type is available: if 2G or 3G has been manually selected and is unavailable, the other type may need to be selected.

Protect the wider control system from the consequences of communication failures. A cellular link can experience delays or loss of service, so it should not be relied upon as the sole path for critical safety functions. The equipment documentation calls for appropriate hard-wired safety interlocks where hazards exist, application testing before service, and approved software for the hardware.

Plan for a verifiable deployment

For a reliable SR2MOD02 or SR2MOD03 installation, confirm the controller pairing, modem version, local network support, power supply, antenna placement, and RS-232 configuration before commissioning. Then verify serial response, SIM readiness, signal quality, network registration, and LED status. This structured sequence helps distinguish wiring and configuration problems from cellular coverage or registration issues, while keeping safety functions independent of the wireless communications path.

Access Official Technical PDF

About The Author