Access Official Technical PDF

Share Summary:LinkedInEmail

For engineers evaluating materials that must retain their properties through changes in temperature, glass transition temperature provides an important point of reference. It marks the transition of an amorphous material from a hard, brittle state toward a softer, more mobile condition. In sodium borate and sodium borophosphate glasses, thermal analysis can help identify this transition and show how changes in composition affect the measured response.

Glass transition temperature is not a melting point. Rather, it describes a change in the behavior of the amorphous structure as the material is heated. Measuring it alongside crystallization behavior helps characterize a glass system and assess its response to thermal processing or storage conditions. X-ray diffraction (XRD) provides complementary evidence by helping distinguish amorphous samples from crystalline materials.

Why glass transition temperature matters

Glass properties depend on their composition and structure. A glass transition measurement offers a practical way to compare formulations and observe how compositional changes relate to softening behavior. This is relevant in materials development and in applications where glass properties must be considered alongside those of other materials. Glasses, for example, have been used in metal-ceramic seals, where matching thermal expansion and maintaining thermal and environmental stability are important considerations.

The transition is described as reversible: below the transition region, the material is typically hard and brittle; as it passes through the region, it becomes softer and more rubber-like. The exact behavior depends on the material. Accordingly, a measured transition temperature should be interpreted in the context of the glass composition and the measurement method, rather than treated as a universal value for all glasses.

How thermal analysis characterizes glass

In the reported investigation, sodium borate and sodium borophosphate glass samples were prepared using a melt-quench process. The batches were melted, poured into molds or onto a metal plate, and annealed before characterization. This preparation produced glass samples for structural and thermal evaluation.

XRD was used to check whether the samples had a crystalline structure. The recorded patterns showed broad diffuse features rather than sharp Bragg peaks, supporting the identification of the samples as amorphous. This structural check matters because the thermal response of a glass should be interpreted with a clear understanding of whether the sample is amorphous or crystalline.

Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were then used to examine the samples during heating. In this work, measurements were conducted up to 800°C at a heating rate of 40°C per minute. The glass transition temperature was identified from the inflection associated with an endothermic change in the thermal signal. Crystallization behavior was also assessed: the onset indicates where crystallization begins, while the exothermic peak marks its maximum signal.

Composition changes measured transition behavior

The results show that composition influenced the measured glass transition temperature. For the sodium borate samples, the reported glass transition temperatures were 472.47°C at 30 mole percent Na2O and 472.50°C at 35 mole percent Na2O. The difference between these two measurements is small. Their crystallization temperatures were 556.75°C and 543.11°C, respectively, showing that the reported crystallization response also differed between compositions.

For sodium borophosphate glass, the reported glass transition temperature rose from 447.64°C at 15 mole percent P2O5 to 467.95°C at 25 mole percent P2O5. The corresponding crystallization temperatures were 538.78°C and 533.08°C. These measurements indicate that the addition of phosphorus pentoxide was associated with a higher measured transition temperature across the two reported compositions, while the crystallization temperatures did not follow the same upward trend.

These results illustrate why transition and crystallization temperatures should be considered separately. They describe different thermal events, and a change in composition may affect each differently. The measurements also apply to the specific glass formulations and test conditions reported; they should not be assumed to predict the behavior of other compositions without testing.

Practical considerations for materials evaluation

For technical teams comparing glass formulations, a useful evaluation process combines structural confirmation with thermal measurement:

  • Confirm the material structure: Use XRD to check for crystalline peaks and support identification of an amorphous phase.
  • Record the test conditions: Heating rate and temperature range are essential context when reporting thermal-analysis results.
  • Identify distinct thermal events: Distinguish the glass transition from crystallization onset and peak behavior.
  • Compare like with like: Interpret composition-related differences using samples and measurement conditions that can be meaningfully compared.

TGA-DTA provides a way to observe thermal changes in a sample, but the results are most useful when paired with a clear description of composition and preparation. In the reported work, the authors also noted that glass transition temperature can be relevant to stability during storage. For engineering decisions, the measured value should therefore be treated as one part of a broader assessment of the material and its intended conditions.

Conclusion

Glass transition temperature is a useful parameter for understanding how an amorphous material responds to heating. XRD can support confirmation of glass structure, while TGA-DTA can identify the transition and reveal crystallization behavior. Measurements on sodium borate and sodium borophosphate glasses show that composition can influence these thermal responses, but not necessarily in the same way. For materials evaluation, the practical lesson is to measure and report each thermal event separately, with the formulation and test conditions clearly defined.

Access Official Technical PDF

About The Author