Access Official Technical PDF

Share Summary:LinkedInEmail

The GuardShield Micro 400 safety light curtain is a compact electro-sensitive protective device designed for point-of-operation and perimeter safeguarding. Its slim 15 × 20 mm housing can suit installations where space is limited, including applications where the transmitter and receiver are recessed into machine frames. Safe use depends on more than selecting a protective height: the system must be paired with the correct controller, positioned at a calculated safety distance, and integrated into a suitable machine safety circuit.

How the GuardShield Micro 400 system works

A Micro 400 system consists of a transmitter and receiver connected to a dedicated MSR41 or MSR42 safety controller. The transmitter sends sequential infrared light pulses across the protective field. When the receiver detects the pulses and the field is clear, the controller can energize its safety outputs, known as Output Signal Switching Devices (OSSDs). If an object interrupts the field, the controller switches those outputs off.

The MSR41 provides on/off functionality. The MSR42 supports additional configured functions, including fixed or floating blanking, muting, external device monitoring (EDM), and start/restart interlock. It can also connect with other safety devices that have suitable PNP outputs. These functions are configured through the controller, so the relevant controller instructions and configuration documentation are part of the system design.

The Micro 400 is a Type 4 electro-sensitive protective equipment (ESPE) device. Standard models are available with 14 mm or 30 mm resolution and protective heights from 50 mm to 1,200 mm, depending on configuration. The stated maximum protective field width is 5 m. A qualified person must install, commission, and service the equipment.

Choosing configurations and cascading light curtains

For applications that need protection on more than one side of a machine, cascadable Micro 400 segments can connect multiple protective fields in series and share a common set of safety outputs. This can provide, for example, front-and-back protection or a combined vertical and horizontal field. Cascading can also reduce the need for separate safety output wiring for each segment.

A system may contain up to three light-curtain pairs: no more than two cascading segments plus one standard Micro 400 pair. The standard pair must be the final segment; cascading pairs cannot be used as standalone systems. Total system length, including light curtains and connection cables, must not exceed 10 m, and the system must not exceed 255 beams per controller. Cascaded segments may use mixed 14 mm and 30 mm resolutions where the configuration requirements are met.

Segment response times add together. The complete system response time includes the response time of each cascaded pair, the standard pair, the MSR41 or MSR42 controller, and other devices in the stop circuit. Blanking, muting, stop-delay settings, and an MSR45E relay expansion module can also affect response time. Verify the configured values rather than relying on the response time of one light-curtain segment.

Calculate safety distance before mounting

The safety distance is the minimum separation between the protective field and the machine hazard. It must account for the time needed to detect access and stop hazardous motion. A calculation that omits any part of the stop circuit can leave the operator exposed before the machine reaches a safe state.

For installations using the European method described in the instructions, the initial calculation is S = 2000 × T + 8 × (d − 14), where S is the safety distance in millimetres, T is the combined machine stopping time and protective-device response time in seconds, and d is light-curtain resolution in millimetres. If the result is greater than 500 mm, recalculate using S = 1600 × T + 8 × (d − 14). Apply the relevant standards and requirements for the installation location, and include the configured system response time.

In the United States, the instructions describe OSHA and ANSI calculation approaches. The ANSI method includes machine stop time, control-system response time, protective-device response time, any applicable brake-monitor allowance, and a penetration-depth factor. The appropriate method depends on the application and applicable requirements. Regardless of the calculation, the instructions specify that Micro 400 light curtains must not be mounted closer than 152.4 mm (6 in.) from a point-of-operation or pinch-point hazard.

Installation, alignment, and machine integration

Mount the transmitter and receiver on a rigid, flat base that resists shock and vibration. Keep their longitudinal axes parallel, orient both units in the same direction, and do not rotate one unit 180 degrees relative to the other. Indicator LEDs help identify alignment and adequate signal strength. After aligning, test the protective function with the specified test rod and confirm that inserting it anywhere in the protective field causes an interruption.

The safeguarding layout must prevent access to the hazard without passing through the sensing field. It must also prevent a person from stepping or standing between the protective field and the hazardous machine parts. Additional mechanical safeguarding or a horizontal cascaded segment may be needed, depending on the risk assessment and machine layout. If multiple light curtains are installed close together, arrange their transmitters and receivers to reduce optical interference; a physical barrier may be needed where units face one another.

Connect the light curtain to an MSR41 or MSR42 using the specified prefabricated cables. The standard system uses separate transmitter and receiver patchcords, with M12 connectors at the light curtain and RJ45 connectors at the controller. The safety outputs must interface with machine controls in a manner appropriate to the required safety integrity. A general-purpose PLC or relay that does not meet the necessary safety requirements is not a suitable substitute for a control-reliable safety interface.

Special environments and configuration changes

The IP69K option encloses the transmitter and receiver in factory-sealed polycarbonate tubes. The controller remains IP20 and must be installed in a suitable enclosure. Follow the specified cleaning practices for the tube, avoid abrasive or aggressive cleaning materials, and check alignment and safety function after cleaning.

Blanking changes the effective resolution and response time of the system. When blanking is configured, update the safety-distance calculation and identify the configured values on the required label. More generally, after any system configuration change, test the protective system and recalculate the safety distance; repositioning may be necessary.

Practical implications for machine safety

The Micro 400 offers a compact way to implement machine guarding, but its protective function depends on the complete safety system. Select the appropriate controller and light-curtain configuration, observe cascading limits, account for the total response time, calculate the safety distance, and verify that the machine interface and physical layout prevent access to hazards. Installation and commissioning should be performed by qualified personnel, with inspections and configuration records maintained as part of the machine’s safety documentation.

Access Official Technical PDF

About The Author