Access Official Technical PDF

Share Summary:LinkedInEmail

In a PLC-based motor control system, the controller must exchange data with the drive that operates the motor. Yet the structure of that data—and the programming tools used to handle it—can differ between manufacturers and drive types. A PLC-drive communication interface aims to make this exchange more consistent, reducing dependence on a particular communication structure while retaining the functions needed for control.

This matters to automation engineers and system integrators working with inverter drives, servo drives and PLC platforms from different vendors. Understanding where communication differences arise is the first step toward designing an interface that is easier to reuse and adapt.

Why PLC and drive communication matters

A PLC coordinates control tasks by processing input information and issuing commands to connected equipment. For electric motor control, a drive provides the link between the PLC’s commands and the motor’s operation. An inverter drive is used to control motor speed, while a servo drive is used to adjust motor position.

The controller and drive must exchange the data required for the intended operation. If the data is not organized and interpreted correctly on both sides, the control program cannot reliably communicate its commands or make use of information returned by the drive. Communication is therefore not an incidental configuration step: it is part of the motor-control architecture.

Different manufacturers, different data structures

Drive manufacturers define communication structures that determine how the PLC and drive represent and exchange data. In the systems considered here, Siemens uses structures called telegrams, while Rockwell Automation uses structures referred to as data types. Both serve the purpose of enabling communication between a PLC and a drive, but they are not interchangeable formats.

This variation creates a practical challenge when a project includes different drive families or controller platforms. The PLC program must account for the structure expected by the particular drive and its manufacturer. A solution built around one structure may require adaptation when the equipment changes, even when the broader control objective remains similar.

Programming tools can add another constraint. Siemens provides pre-set blocks that help programmers implement communication and control. These blocks can simplify setup, but they may also limit how the programmer or user can manipulate the communication. An interface block can provide a way to separate the application’s control requirements from the manufacturer-specific structure underneath.

What a PLC-drive communication interface is intended to do

The interface described in the technical work was designed to support communication between a PLC CPU and a drive regardless of drive type and manufacturer. Its aim is to provide a common point for handling communication, rather than requiring the application to be built directly around each vendor’s data structure.

In practical terms, this approach places an interface between the PLC program and the drive communication details. The interface must still accommodate the structure used by the selected equipment; it does not remove the need to configure or understand the drive. Instead, it seeks to make the application less dependent on the communication format and pre-set programming blocks associated with a specific system.

That distinction is important for project planning. A common interface can support a more consistent programming approach, but the supported devices and required functions must be verified. The work examined Siemens telegrams and Rockwell Automation data types because they represent notably different approaches to structuring communication.

Testing the interface across drive applications

The interface was implemented and tested using several PLC-and-drive combinations. Tests included a Siemens PLC with a Siemens inverter drive, a Siemens PLC with a Siemens servo drive, and a Rockwell PLC with a Rockwell inverter. The test program also covered Siemens communication structures including Standard Telegram 1, Siemens Telegram 352 and Standard Telegram 111, as well as a Rockwell Automation inverter data type.

The reported results were positive: the required interface features were executed, and communication between the PLC CPU and drive was successful in the tested cases. These results provide evidence that an interface can be applied across the examined drive types and manufacturer-specific structures. They should not be interpreted as a guarantee of compatibility with every PLC, drive, firmware version or communication configuration.

For engineers evaluating a similar approach, validation should reflect the actual project. Confirm that the interface covers the commands and information the application needs, and test it with the selected controller, drive and communication structure. Include the expected inverter or servo functions in the test plan rather than treating successful data exchange alone as proof that the complete control task is covered.

Practical considerations for integrators and plant teams

A reusable interface can be valuable when equipment choices vary across machines or projects, but it should be treated as a defined engineering component with clear limits. Before deployment, teams should document:

  • Which PLC platforms and drive structures have been implemented and tested.
  • Which control functions the interface is expected to support.
  • Where manufacturer-specific setup or programming remains necessary.
  • How the interface will be validated when a drive or controller is changed.

These points help system integrators and plant teams distinguish between a common programming layer and the device-specific configuration that remains essential. They also make it easier to assess whether an interface is suitable for a particular retrofit, new machine or multi-vendor environment.

Conclusion

PLC-drive communication depends on data structures that vary between manufacturers and drive types. Siemens telegrams and Rockwell Automation data types illustrate how those differences can affect implementation, while pre-set programming blocks may constrain user manipulation. A PLC-drive communication interface offers a way to organize that complexity behind a more consistent application-level approach.

The practical value depends on the scope of the interface and the quality of its validation. Testing with the intended PLC, drive and communication structure is essential before relying on it in production. A further development identified in the technical work is a converter between software environments, which could extend the concept beyond drive communication to greater freedom in the choice of programming software.

Access Official Technical PDF

About The Author