The WM8944B audio CODEC brings analogue and digital audio conversion, configurable signal processing, output mixing, and a current-mode video buffer together in a compact device. For engineers developing embedded multimedia equipment, its main design value is the ability to configure several parts of an audio chain—input selection, filtering, dynamic-range processing, and output routing—within one component. Understanding those paths and their dependencies is essential when assessing whether its features fit a particular design.
WM8944B audio CODEC signal paths
On the input side, the device supports up to two analogue audio inputs, IN1 and AUX. These can be configured for single-ended or pseudo-differential use. An input programmable gain amplifier (PGA) feeds the ADC, while a separate bypass route can send analogue input signals directly to the output mixers. An integrated microphone-bias reference supports electret microphones.
The device also includes a stereo digital microphone interface. Its digital microphone data can feed the DSP core, providing an alternative to the analogue PGA and ADC route. The ADC and DAC support sample rates from 8 kHz to 48 kHz, and audio data connects to other digital systems through an I2S-compatible interface.
On the output side, mixers combine signals from digital audio paths or analogue bypass paths. The available outputs include a mono line output and a mono bridge-tied-load (BTL) headphone or speaker drive. This gives designers options for routing playback and bypass signals, but the intended output configuration should be established early because it affects mixer settings, supply requirements, and board connections.
Configurable DSP for recording and playback
The WM8944B’s DSP functions support processing on the ADC recording path, the DAC playback path, or a division of functions between them. Available processing includes low-pass and high-pass filters, five notch filters, a five-band equalizer, dynamic range control, and a programmable Direct Form 1 (DF1) filter. A digital beep generator can also add tones to the DAC output path.
These functions address different signal-chain needs. Notch filters can attenuate narrow frequency bands, while the equalizer provides frequency-dependent adjustment. The ADC high-pass filter can remove DC offsets and reduce low-frequency noise, including sources such as mechanical vibration or wind noise. Dynamic range control includes compression, limiting, and noise-gate functions, which can be configured for recording or playback use.
ReTune is a configurable digital filter intended to compensate for imperfect acoustic characteristics in an application’s housing, loudspeaker, or microphone. It can apply acoustic equalisation and selective phase, or delay, control to specific frequency bands. Its coefficients are not a preset guarantee of a particular acoustic result: the device documentation specifies that suitable settings are determined using Cirrus Logic’s WISCE software together with bench testing and audio reference measurements.
Clocking, control, and power integration
Configuration is handled through either an I2C or SPI control interface. A single external clock provides a timing reference for digital functions, while the integrated frequency-locked loop (FLL) supports frequency conversion and can help address noise or jitter in the external clock. The FLL offers configuration options for different power and reference-filtering requirements. Clock selection and audio-interface timing therefore need to be considered alongside the required sample rate and system architecture.
The device also integrates an LDO regulator for low-noise supply regulation and compatibility with a range of supply rails. The specified recommended operating ranges are 1.62–1.98 V for the digital core, 1.62–3.6 V for the digital I/O supply, 2.4–3.6 V for the analogue supply, and 1.71–3.6 V for the speaker supply. These are separate supply domains, so the system design must account for the applicable rail and operating conditions rather than treating the CODEC as a single-supply component.
Power management involves more than enabling the desired audio blocks. For example, enabling the input PGA also requires the VMID reference and bias current. The device provides recommended power-up and power-down sequences, as well as thermal shutdown and reset functions. Following the documented sequencing and checking thermal conditions in the intended PCB and enclosure helps avoid treating register configuration as an isolated software task.
What the integrated video buffer adds
In addition to audio functions, the WM8944B includes a current-mode video buffer with an input, reference connection, and output. Its specified function is video-signal buffering, and its response includes a third-order low-pass characteristic. The buffer’s gain is configurable, with a stated 6 dB gain step. Designers should evaluate the buffer using the electrical characteristics and recommended external components for their signal and load conditions; its presence does not remove the need to design the surrounding video path.
Practical design considerations
The device is supplied in a 25-ball W-CSP package measuring 2.41 × 2.41 mm. That compact footprint can suit space-constrained portable designs, but board layout and assembly still require attention. The documentation highlights thermal paths through the package and PCB, and notes that connecting ground balls through thermal vias to a ground plane can aid heat extraction. Supply decoupling, microphone-bias components, output connections, and video-buffer components should also follow the application guidance.
When evaluating the WM8944B, engineers can use a practical checklist:
- Choose analogue, digital microphone, or bypass input routes to match the signal sources.
- Decide which DSP functions belong on the record path and which belong on playback.
- Confirm output mixer routing and whether the application needs line output, mono BTL drive, or both.
- Verify clocking, control-interface mode, supply rails, and required power-up sequencing.
- Review external components, PCB thermal design, and the video buffer’s loading and gain requirements.
Conclusion
The WM8944B combines flexible audio routing and DSP with microphone support, mono outputs, clock-generation options, an LDO, and a video buffer. Its integration can simplify the functional architecture of a compact multimedia design, but successful implementation depends on matching the configurable signal paths to the application and carefully managing clocks, supplies, external components, and startup sequence. Those details—not the feature list alone—determine how well the device fits a specific embedded system.