High-brightness semiconductor lasers could offer industrial automation and manufacturing systems a compact source of concentrated, controllable light. Potential applications include material processing and sensing, including LiDAR. A key challenge is increasing optical power and emission area without allowing the beam to spread or become difficult to focus. A double-lattice photonic-crystal resonator addresses that challenge by helping a broad-area semiconductor laser maintain single- or low-order lateral-mode operation.
Why brightness is difficult to scale
Laser brightness describes how much optical power is emitted per unit area and per unit solid angle. In practical terms, it indicates how tightly a beam can be focused or how narrowly it diverges. Increasing the emitting area can raise brightness, but only if the beam remains in a suitable lateral mode.
When a semiconductor laser operates in higher-order lateral modes, its brightness falls as the mode order increases. Larger emission areas can therefore trigger a trade-off: the device has more area from which to emit, but also a greater tendency to support modes that degrade beam quality. This limitation has kept the brightness of many semiconductor lasers below that of established gas and fibre or disk laser sources.
Edge-emitting lasers have achieved high power and brightness, but can produce beams with substantial divergence and asymmetry. Some designs also exhibit astigmatism that varies with injection current. These characteristics make focusing more complicated, sometimes requiring additional optical components to correct the beam. Surface-emitting architectures offer a different approach, although conventional vertical-cavity surface-emitting lasers also face multimode operation when their resonators are expanded.
How a double-lattice photonic-crystal resonator works
Photonic-crystal lasers use a periodic structure to control how light propagates and resonates. In the double-lattice design, two groups of lattice points are superimposed, with one shifted relative to the other. The separation between the groups can be selected to change how the light waves diffracted by the structure interact.
The central design goal is to weaken direct 180-degree coupling between fundamental waves while maintaining the coupling needed for surface-emitting resonance. With the two lattice groups separated by about one-quarter of the lattice constant, the structure can suppress this direct coupling. That changes the distribution of light in the resonator: light spreads more evenly across the cavity, a behavior described as “flattening.”
This redistribution helps distinguish the fundamental mode from higher-order modes. Higher-order modes have more of their energy near the cavity edges, where more light can be lost. Increasing their optical loss relative to the fundamental mode makes them less likely to reach the threshold for lasing. The resonator can therefore support a wider emission area without the same loss of mode stability seen in a conventional single-lattice design.
Demonstrated output and beam characteristics
A fabricated device with a 500-micrometre-diameter emission region produced a peak output exceeding 10 W under pulsed operation. Its beam divergence was below 0.3 degrees in both measured directions, and the reported brightness exceeded 300 MW cm-2 sr-1. These results show the importance of combining a large emitting area with control of lateral modes: expanding the aperture alone would not deliver the same benefit if higher-order modes degraded the beam.
A second device, designed for continuous-wave operation, used an 800-micrometre resonator and a distributed Bragg reflector beneath the photonic crystal. The reflector directed downward light back toward the output and was intended to improve slope efficiency and reduce heat generation. The device delivered up to about 7 W continuous-wave output. At an output of 3.7 W, measured divergence was 0.17 degrees along one axis and 0.21 degrees along the other, with a reported brightness of about 180 MW cm-2 sr-1.
The continuous-wave measurements also illustrate practical considerations beyond resonator design. The near-field pattern was less uniform than in the pulsed device. The authors associated this with reduced pattern-writing accuracy during fabrication and expected temperature distribution across the photonic-crystal plane to affect light confinement. In a production setting, both pattern fidelity and thermal management would therefore matter when translating the optical design into a stable device.
Design implications for industrial laser systems
The double-lattice structure offers a way to manage the mode competition that typically limits broad-area semiconductor lasers. Its potential is not limited to the specific geometry used in the demonstrated devices. Calculations indicate that adjusting the separation between the lattices can also tune the interaction of 90-degree-diffracted waves with 180-degree-diffracted waves. With a suitable phase relationship, the waves can interact destructively, further increasing the loss difference between fundamental and higher-order modes.
In the modeled optimized structure, a sufficiently wide threshold-gain difference was maintained for resonators up to 2,500 micrometres in diameter. The analysis suggests the possibility of brightness in the range of 1–10 GW cm-2 sr-1. These are theoretical projections, not demonstrated operating results, and should be distinguished from the measured pulsed and continuous-wave performance.
For system integrators and equipment designers, the practical significance is the possibility of obtaining a narrow, more symmetric beam directly from a semiconductor source. The work points toward applications such as material processing and LiDAR, where beam focus and divergence influence how light is delivered or collected. It does not establish that a particular industrial system can dispense with beam-shaping optics; that depends on the requirements of the application and the source configuration.
Conclusion
Double-lattice photonic-crystal resonators address a central scaling problem for high-brightness semiconductor lasers: maintaining low-order lateral-mode operation as the emission area grows. Demonstrations achieved high pulsed output with narrow, symmetric divergence, as well as multi-watt continuous-wave output. Further brightness gains remain a modeled prospect, but the approach provides a design path for semiconductor sources aimed at demanding sensing and processing applications. For industrial decision-makers, its value lies in combining broad-area emission with deliberate control of beam quality, while recognizing that fabrication accuracy and thermal behavior remain important engineering considerations.