For industrial automation networks, data center interconnects and other bandwidth-intensive systems, extending optical links without adding excessive signal-processing complexity is an important design goal. 1060 nm VCSELs offer one approach: they retain the advantages of GaAs-based vertical-cavity surface-emitting lasers while operating at a wavelength where multimode fiber (MMF) can have lower attenuation and chromatic dispersion than at 850 nm. Experimental results show how this combination can support longer-reach links, while also revealing practical design tradeoffs.
Why consider 1060 nm VCSELs for long-reach links?
VCSEL-MMF links at 850 nm are widely used for short-reach optical connections. Their appeal includes low manufacturing and packaging costs, tolerance to alignment variation, compact size and energy-efficient operation. However, as link distances and data rates increase, fiber impairments become more significant.
Chromatic dispersion spreads signal components that travel at different speeds through the fiber. At 850 nm, its reported value is about −85 ps/nm/km. Fiber attenuation also exceeds 2 dB/km, which can make the optical power budget more challenging as reach increases. These effects can limit high-speed links beyond roughly 1 km, particularly when designs aim to avoid extensive digital signal processing (DSP) and forward-error correction (FEC).
Moving to 1060 nm improves both measures. The paper reports chromatic dispersion of about −33 ps/nm/km and attenuation of 0.95 dB/km for the wavelength-optimized fiber used in its transmission experiments. This is not the same as eliminating dispersion or loss, but it reduces two sources of impairment relative to 850 nm operation.
Wavelength selection also involves a technology constraint. Although 1310 nm offers near-zero chromatic dispersion and lower MMF attenuation, conventional GaAs-based VCSEL technology can be extended only to approximately 1100 nm without compromising reliability. A wavelength near 1060 nm therefore provides a practical route to improved fiber performance while retaining a GaAs-based laser approach.
Matching the multimode fiber to the wavelength
Changing the laser wavelength is only part of the link design. The fiber’s refractive-index profile must also suit the operating wavelength so that different modes arrive with less timing variation, known as differential mode delay. For graded-index MMF operating at 1060 nm, the fiber profile’s alpha-value needs to be lower than for 850 nm designs: approximately 2.06 rather than 2.10.
The prototype fiber used in the reported work had a 50 µm core and an alpha-value of about 2.06. Its measured modal bandwidth exceeded 5 GHz·km at 1060 nm. These characteristics illustrate why a longer-wavelength VCSEL should be evaluated as part of a matched optical link, rather than treated as a drop-in laser substitution for an existing 850 nm system.
Single-mode VCSEL design balances speed and launch control
The work presented two 1060 nm VCSEL designs derived in part from high-speed 850 nm designs. Both used multiple oxide apertures, which provide current and optical confinement while helping reduce capacitance. One design supported multimode operation; the other was engineered to favor single-mode emission through weaker transverse optical guiding and stronger confinement of optical gain.
The single-mode device had a 4 µm oxide aperture and suppressed higher-order modes by more than 50 dB under the measured conditions. Its modulation bandwidth exceeded 22 GHz at 25 °C and was 15.6 GHz at 85 °C. In binary NRZ, or on-off keying (OOK), back-to-back tests reached data rates up to 50 Gbps at 25 °C and 40 Gbps at 85 °C. The multimode device reached up to 40 Gbps at 25 °C and 35 Gbps at 85 °C.
These are back-to-back results, not transmission distances over the prototype MMF. They demonstrate the laser devices’ modulation performance, while the fiber experiment provides a separate measure of link reach.
Mode-selective launch enables 1,000 m transmission
In the long-reach test, the single-mode VCSEL was coupled into the lowest-order mode group of the MMF using a lens system. This mode-selective launch, combined with the VCSEL’s narrow spectral width, helps limit the effects of modal and chromatic dispersion. The approach requires more precise alignment than a broad multimode launch, making optical coupling and assembly tolerances important system considerations.
Using binary NRZ/OOK over 1,000 m of 1060 nm-optimized MMF, the test achieved error-free transmission at 25 Gbps without equalization or FEC. At that rate, the reported average received optical power was −4 dBm using a PRBS-15 test pattern. Increasing the pattern length from PRBS-7 to PRBS-15 produced a 1.5 dB penalty; testing with PRBS-31 showed no further penalty. A preliminary alignment assessment indicated an approximate ±5 µm tolerance for error-free 25 Gbps transmission over this distance.
The result demonstrates the potential of 1060 nm VCSEL-MMF links, but it should be interpreted within the test conditions: a prototype fiber, mode-selective launch and a particular VCSEL. It does not establish identical reach or alignment performance for every fiber, transceiver package or installed link.
Design implications for system integrators
For engineers assessing longer optical connections, the findings point to several linked decisions:
- Specify the fiber for the wavelength. The MMF index profile influences modal delay and should be appropriate for 1060 nm operation.
- Evaluate launch conditions. A single-mode VCSEL can support selective excitation of fiber modes, but tighter alignment requirements may affect coupling and packaging design.
- Separate device and link performance. Back-to-back data rates describe VCSEL modulation capability; fiber transmission results depend on the complete optical path and test setup.
- Consider signal processing against system needs. The demonstrated 25 Gbps, 1,000 m link required no equalization or FEC. Higher rates or longer distances may require equalization, FEC, multilevel modulation or other signal-processing techniques.
Conclusion
1060 nm VCSELs can extend the reach potential of multimode optical interconnects by pairing high-speed GaAs-based lasers with fiber that offers lower attenuation and chromatic dispersion than at 850 nm. The reported demonstration achieved error-free 25 Gbps transmission across 1,000 m using a single-mode VCSEL and mode-selective launch. For practical deployment, the central engineering task is to treat laser, fiber profile and optical alignment as one system—and to assess any need for DSP or FEC against the target distance, data rate and implementation constraints.