For concentrating solar power (CSP), a receiver coating must absorb incoming sunlight while limiting the heat it radiates back to its surroundings. This balance becomes more demanding as operating temperatures rise. Research into solar selective coatings based on metal and metal-silicide nanoparticles points to a design path for CSP receivers operating at 750°C, where both optical performance and resistance to oxidation are important.
Unlike conventional black coatings, which absorb broadly across the spectrum, a selective absorber is designed to take in solar wavelengths and reflect more of the longer-wavelength radiation associated with thermal emission. Nanoparticle-pigmented coatings offer a way to tune this spectral response through the particle material and size, the pigment concentration, and the thickness of the coating.
Why selective coatings matter at higher CSP temperatures
CSP systems concentrate sunlight onto a receiver, where the absorbed energy becomes heat carried by a heat-transfer fluid. Thermal energy storage can help make this energy available beyond periods of direct sunlight. Raising receiver operating temperatures can also support more efficient power conversion, but it increases the demands on receiver materials and coatings.
A coating that absorbs solar energy effectively but emits substantial heat at operating temperature can lose an important share of the collected energy. This is a particular concern for black paints, which do not strongly distinguish between incoming solar radiation and the receiver’s longer-wavelength thermal radiation. A selective coating seeks to maintain high solar absorptance while reducing thermal emittance.
How nanoparticle-pigmented coatings control the spectrum
In a pigmented cermet coating, metal or metal-silicide nanoparticles are dispersed in a dielectric matrix. When particles are larger than a few nanometers, their scattering and absorption both contribute to the coating’s optical behavior. That makes particle size and material properties central to the design.
The research modeled nanoparticle scattering and absorption using Lorenz-Mie theory, then used a four-flux radiative transfer method to estimate the coating’s reflectance. The model accounts for light traveling through the coating in both collimated and diffuse directions, as well as reflections at the coating’s boundaries. Predicted reflectance can then be used to estimate optical-to-thermal conversion efficiency at a specified operating temperature and solar concentration.
This modeling approach provides a practical way to evaluate design choices before fabrication. It also identifies a useful material-selection principle: nanoparticles with a sharp change in refractive index and extinction coefficient near the desired spectral cutoff can produce a more selective reflectance profile.
Design variables that influence coating efficiency
Particle material and diameter
The study compared several transition metals and silicides. Among the materials evaluated, C54-TiSi2 delivered the highest modeled efficiency, with NiSi also performing well. These silicides were promising because their optical properties supported a sharper transition between solar absorption and infrared reflection than some of the other candidates.
Smaller particles generally supported higher modeled efficiency in the Ni-based system. The calculations also indicated that changing particle radius within the 10–20 nm range had only a small effect on maximum efficiency. That relative insensitivity suggests that some variation in particle size may be manageable when the average particle size remains small.
Pigment concentration and coating thickness
For a given particle system, performance depends strongly on the combined effect of nanoparticle volume fraction and coating thickness. This relationship gives coating designers flexibility: a lower particle concentration can be paired with a thicker layer, or a higher concentration with a thinner one, while targeting similar optical behavior.
That flexibility matters for manufacturing. Particle dispersion, thickness control, and coating durability all influence process decisions. The modeled designs also showed regions where efficiency changed little across a range of thickness and volume-fraction combinations, suggesting that a carefully selected design may tolerate some fabrication variation.
Substrate and infrared reflection
The substrate stack also affects thermal losses. Adding a tantalum layer beneath the absorber was modeled as a way to increase infrared reflectance while retaining low reflectance in the solar range. The modeled benefit was greater at a solar concentration ratio of 100 than at 1,000, consistent with thermal-emittance losses having a larger influence at lower concentration.
Performance and thermal stability findings
For optimized TiSi2-pigmented coatings at 750°C, the model predicted optical-to-thermal conversion efficiencies of 87.0% at a concentration ratio of 100 and 94.4% at 1,000. An experimentally tested, unoptimized coating using 200 nm TiSi2 particles in silicone reached 89.8% at 1,000 concentration and 750°C. The study reported this result as close to the cited commercial Pyromark 2500 coating efficiency of 90.1% under the same stated conditions.
The work also examined thermal stability in air. Ni/NiSi core-shell structures embedded in a silicon-rich oxide matrix remained stable at 750°C during a 1,000-hour test. The results support the potential of interfacial silicide formation to limit further oxidation in this system. The reported stability is specific to the studied materials and test conditions; coating designs still require validation for their intended receiver, substrate, and operating environment.
Practical implications for CSP receiver design
For engineers and system integrators assessing high-temperature receiver coatings, the findings highlight several connected design considerations:
- Define the operating conditions. Operating temperature and solar concentration affect the tradeoff between solar absorption and thermal emission.
- Select pigments for spectral behavior. Particle optical properties near the target cutoff wavelength can influence achievable selectivity.
- Balance concentration and thickness. The combination of pigment volume fraction and coating thickness can offer manufacturing flexibility.
- Evaluate the full layer stack. An infrared-reflective underlayer may reduce losses, depending on the system’s concentration conditions.
- Validate thermal durability. Optical performance alone is not enough; oxidation resistance and compatibility with the substrate and coating process must also be considered.
Overall, nanoparticle-pigmented solar selective coatings offer a tunable approach to receiver design for CSP systems targeting higher operating temperatures. The reported modeling and experiments identify TiSi2 and NiSi as promising materials and show why particle properties, coating geometry, substrate reflectance, and thermal stability should be considered together. For industrial teams, the practical next step is to evaluate these variables against the receiver’s operating conditions and manufacturing constraints rather than treating coating absorptance as the sole performance measure.