Optical wireless communication (OWC) offers an alternative way to move data through indoor spaces when radio-frequency capacity is constrained or unwanted. Instead of radio waves, these systems transmit modulated infrared or visible light, using sources such as LEDs or laser diodes and a photosensitive receiver. For industrial automation engineers and technical decision-makers, OWC is a potential complement to wired and radio networks—but its suitability depends on coverage, mobility, ambient conditions and link design.
What optical wireless communication can offer
OWC uses portions of the optical spectrum that are not allocated in the same way as radio-frequency bands. This provides access to substantial potential bandwidth. Indoor systems have been investigated for high-speed data transmission, and the technology can support applications such as voice, video and data communications. The source survey reports indoor demonstrations at rates up to 25 Gbps; that figure describes reported systems, not a performance guarantee for a particular installation.
Light also behaves differently from radio. It does not pass through opaque walls, which can limit signal leakage beyond a room and allow the same optical resources to be reused in separate areas. OWC links are also not subject to the same radio-frequency electromagnetic interference as RF systems. These properties may make the technology worth assessing in facilities where radio performance, spectrum availability or room-level signal containment matters.
There are trade-offs. Because light does not pass through walls, access points in different rooms need a wired backbone if they are to connect as part of a wider network. Coverage can also be affected by obstacles, reflections and the position of the transmitter and receiver. OWC should therefore be considered as part of a network design, rather than as a simple wireless substitute for every RF link.
Optical wireless link design: direct paths and reflections
Indoor links are commonly described as line-of-sight (LOS) or non-line-of-sight (NLOS). A LOS link has a direct optical path from transmitter to receiver. It can reduce multipath dispersion and improve power efficiency, but an object blocking the path can interrupt communication. This makes direct, highly directional links less suitable where users or equipment move through the space.
NLOS links use light reflected from surfaces such as walls or ceilings. This can make a connection less dependent on an uninterrupted direct path, but reflections arrive at different times and travel different distances. The resulting delay spread can cause inter-symbol interference (ISI), limiting the channel bandwidth and data rate.
Designers can adjust the directionality of the transmitter and the receiver’s field of view (FOV). A broad transmitter pattern and wide-FOV receiver can support mobility, but collect more reflected light and ambient noise. Narrower fields of view can reduce unwanted rays and dispersion, though they may constrain coverage. Hybrid arrangements combine different degrees of directionality to balance these needs.
Infrared and visible light approaches
Infrared communication
Infrared communication (IRC) uses infrared light to carry data. Indoor IRC designs include diffuse systems, which rely on reflections, and multi-beam arrangements that direct light toward multiple spots. In multi-spot designs, reflected spots can act as secondary sources closer to a receiver, potentially reducing delay spread. Some approaches adapt beam direction or power to the receiver’s location, but this adds design and control complexity and can affect coverage uniformity.
Visible light communication
Visible light communication (VLC) uses lighting sources to provide illumination and transmit data at the same time. That dual role introduces an additional design requirement: communication must coexist with the intended lighting level and brightness control. White light can be produced using phosphor-coated blue LEDs or by combining red, green and blue LEDs. The phosphor approach is widely used because it is less complex, although the phosphor’s response can limit modulation bandwidth. Multi-colour sources can provide separate wavelengths for data transmission.
VLC dimming methods also involve trade-offs. Adjusting the LED’s DC current changes luminous output, but can affect the emitted light’s chromaticity. Pulse-width modulation varies pulse duration while keeping pulse amplitude constant, helping maintain the light spectrum. The choice of dimming method needs to account for both illumination and data requirements.
Receiver choices and common impairments
A basic receiver uses a single photodetector with a wide FOV. It collects light from a broad range of directions, but also receives more background light from sources such as sunlight and incandescent lighting. Ambient light can introduce shot noise or saturate a detector at high intensities. Optical and electronic filtering can reduce some of these effects.
Angle-diversity receivers use multiple narrow-FOV detector branches aimed in different directions. They can reduce ambient-light exposure and signal spread, but require more optical components and can be larger and more complex. Imaging receivers use an optical concentrator, such as a lens, to form an image across multiple detector pixels. This can separate signals arriving from different directions and help reduce multipath effects; the receiver design and pixel arrangement still matter.
Power and detector design impose further constraints. Infrared transmitters must meet eye- and skin-safety requirements, which restrict available optical power. At the receiver, a larger photodetector can collect more light, but its increased capacitance can reduce bandwidth. Detector arrays, lenses and circuit techniques are among the approaches discussed for managing this trade-off.
Assessing OWC for an industrial environment
For system integrators and plant teams, an OWC assessment should begin with the actual communication path and operating conditions. Consider whether direct paths can be maintained, whether reflections are needed for mobility, where ambient light may enter the receiver, and how access points will connect across rooms. For VLC, include lighting and dimming requirements; for IRC, include optical power limits and receiver placement.
The practical implication is that OWC can add a useful high-bandwidth option to indoor network planning, especially where optical links’ room-level containment or separation from RF interference is relevant. But performance depends on the full link—transmitter, channel, receiver and modulation—not just the available optical bandwidth. A design that balances coverage, mobility, noise, dispersion, safety and backbone connectivity is essential before OWC is selected for an operational network.