Access Official Technical PDF

Share Summary:LinkedInEmail

When integrating a Renesas E1 emulator with a compact target board, connector size and placement can affect the available PCB area. The R0E000010CKZ11 E1 emulator connector adapter provides a transition between the 14-pin, 2.54 mm-pitch connector on the E1 user-system interface cable and a 14-pin, 1.27 mm-pitch connector on the user system. Its smaller mating connector can reduce the area occupied by the connection on the board, but designers need to account for its pin assignment and physical clearance requirements.

What the E1 emulator connector adapter does

The R0E000010CKZ11 sits between the E1-specific user-system interface cable and the target system. The cable-side connection uses a 14-pin connector with a 2.54 mm pitch. The adapter’s user-system side connects to a 14-pin, 1.27 mm-pitch connector. This arrangement allows the system board to use a smaller-pitch connector than the one at the cable head.

The user-system connector identified for this arrangement is a Samtec TFM-107-02-L-D surface-mount type or TFM-107-01-L-D through-hole type. The adapter’s upper connector is identified as HTST-107-01-T-DV, and its lower connector as SFM-107-02-L-D-A. Both adapter connectors have a guaranteed insertion-and-removal count of 50 cycles.

Check the pin mapping before designing the board

The adapter does not preserve the standard E1 interface connector pin assignment position for position. This is a key design consideration: a board layout based only on the connector’s physical orientation could connect signals incorrectly. Use the adapter’s CN1-to-CN2 correspondence when creating the schematic, assigning connector pads and checking the PCB layout.

The documented correspondence is:

  • CN1 pin 1 maps to CN2 pin 4.
  • CN1 pin 2 maps to CN2 pins 1 and 14.
  • CN1 pin 3 maps to CN2 pin 8.
  • CN1 pin 4 maps to CN2 pin 11.
  • CN1 pin 5 maps to CN2 pin 10.
  • CN1 pin 6 maps to CN2 pin 12.
  • CN1 pin 7 maps to CN2 pin 2.
  • CN1 pin 8 maps to CN2 pin 3.
  • CN1 pin 9 maps to CN2 pin 13.
  • CN1 pin 10 maps to CN2 pin 7.
  • CN1 pin 11 maps to CN2 pin 9.
  • CN1 pin 12 maps to CN2 pins 1 and 14.
  • CN1 pin 13 maps to CN2 pin 5.
  • CN1 pin 14 maps to CN2 pin 6.

In particular, the table associates both CN1 pins 2 and 12 with CN2 pins 1 and 14. Preserve the documented mapping when designing the user-system connector footprint and verifying the interface. The pin numbers refer to the adapter connectors shown in the product documentation; confirm numbering and orientation against the connector’s key and the board design.

Plan PCB placement and component clearance

The adapter and cable need room around the target-board connector. The product documentation specifies a maximum component height of 5 mm in the defined area around the connector. This restriction applies when the user system uses either listed TFM-107 connector type: the surface-mount TFM-107-02-L-D or through-hole TFM-107-01-L-D.

The clearance drawing also identifies the restricted region and the direction from which the emulator connects. Use those details during mechanical layout, not just after the board has been routed. Components that exceed the 5 mm height limit within the marked area may interfere with the adapter or its connection. Keep the connector orientation key in view when placing the footprint and checking the cable approach.

For an engineering review, verify three items together: connector type, pin numbering and orientation, and component heights in the specified clearance area. Treating these as separate checks can make it easier to overlook a physical or electrical mismatch.

Package contents and handling considerations

The documented package includes one R0E000010CKZ11 adapter, one TFM-107-01-L-D through-hole connector for mounting on the user system, and English and Japanese user manuals. Check the supplied contents before beginning integration, particularly if the board design requires the specified through-hole connector.

The adapter’s guaranteed insertion-and-removal count is 50 cycles for each of its upper and lower connectors. This is a stated connector-use limit, so account for it when planning repeated connection and disconnection during development or servicing. The product documentation also states that repair requests for the adapter cannot be accepted; product questions are directed to a local distributor.

Conclusion: integrate the adapter as part of the interface design

The R0E000010CKZ11 offers a way to connect the E1 emulator’s 2.54 mm-pitch cable connector to a smaller-pitch user-system connector. Successful integration depends on more than fitting the connector footprint: the CN1-to-CN2 pin assignment differs from the standard E1 connector arrangement, the orientation must be correct, and components in the specified area must not exceed 5 mm in height. Confirming these details at schematic, PCB and mechanical review stages helps ensure the adapter can be connected as intended.

Access Official Technical PDF

About The Author