A wide-range vacuum gauge can simplify pressure monitoring across processes that move between rough vacuum, high vacuum and atmospheric conditions. The INFICON BCG450 TripleGauge series addresses this challenge by combining capacitance diaphragm, Pirani and hot-cathode Bayard-Alpert (BA) ionization sensors in one instrument. Understanding how these sensing technologies hand off across the measurement range helps engineers select the right interface, interpret readings and plan installation.
How the TripleGauge combines three sensor technologies
Each sensing method is suited to a different pressure region. The capacitance diaphragm sensor measures from 10 to 1500 mbar and, in this range, operates independently of gas type. The Pirani sensor covers the lower-pressure region using the relationship between gas thermal conductivity and pressure. At still lower pressures, the BA sensor measures the ion current produced when electrons ionize gas molecules.
Rather than requiring an operator to switch between separate gauges, the BCG450 electronics combine measurements from these sensors and provide a continuous output across 5 × 10-10 to 1500 mbar. The measurement signal is logarithmic with pressure. Its analog output spans 0 to 10.13 V, with the measuring range represented by approximately 0.774 to 10.13 V.
Understanding the measurement handoffs
The gauge monitors pressure continuously with the Pirani system. The hot cathode is activated only when pressure falls below 2.4 × 10-2 mbar, helping prevent filament burnout at higher pressures. If pressure rises above 3.2 × 10-2 mbar, the hot cathode switches off. Between the handoff points, the electronics transition between measurements; the output is blended in crossover regions to maintain a smooth response.
At the upper end, the gauge uses the capacitance diaphragm sensor above 10 mbar. Between 1 and 10 mbar, capacitance diaphragm and Pirani measurements are combined. The Pirani sensor covers the intermediate vacuum range, while the BA sensor is used at lower pressures, with another crossover between approximately 5 × 10-3 and 2 × 10-2 mbar.
This architecture reduces gas-type dependence across much of the range, but it does not eliminate it everywhere. The capacitance diaphragm measurement is gas-type independent from 10 to 1500 mbar. In the Pirani and BA regions, readings depend to some degree on the gas. The specified measurement range applies to dry air, oxygen, carbon monoxide and nitrogen; measurements for other gases may require conversion using the relevant gas-dependence information.
Choosing an interface for vacuum gauge integration
The BCG450 is available in versions intended for different control architectures. Standard versions provide analog measurement output and RS232C communication. Fieldbus models add network connectivity and switching functions:
- BCG450-SD: DeviceNet interface.
- BCG450-SE: EtherCAT interface.
- BCG450-SP: Profibus interface.
The gauge can be used with specified INFICON vacuum gauge controllers or with other suitable control equipment. Fieldbus versions are generally integrated with a compatible bus master and communication software. They must not be operated through the RS232C interface or with the VGC40x/VGC50x controller’s RS232C connection, as this can cause data transmission errors.
For system integrators, interface selection affects more than how pressure data reaches the controller. The fieldbus variants also provide configurable switching functions, while the standard BCG450 includes an atmospheric-pressure switching function with a relay output. Confirm the model, control protocol, cable requirements and available relay functions before specifying the gauge. The fieldbus models require their corresponding bus connections, and the DeviceNet version also needs a separate supply for its interface.
Installation and operating considerations
The gauge is designed for measuring gases and must not be used to measure flammable or combustible gases in mixtures containing oxidants when those mixtures are within the explosion range. Process media, contamination and the possibility of reactions caused by heat must also be considered as part of the system risk assessment.
Mechanical and electrical installation affect reliable operation. The gauge must be electrically connected to the grounded vacuum chamber; for a KF connection, this requires a conductive metallic clamping ring. Keep vacuum-facing parts clean, use clean tools and lint-free gloves, and do not open clamps while the system is pressurized. In applications where particles or deposits could affect the electrodes, the optional baffle is recommended. A horizontal-to-upright mounting position can also help limit condensate or particles entering the measuring chamber.
After power-up, allow approximately 10 minutes for stabilization. The gauge adjusts automatically, so routine manual adjustment is not required. Its display-equipped versions show pressure and units, with a red background when an error is indicated. The pressure unit can be selected from mbar, Torr or Pa on the standard model through its serial interface.
Managing contamination and sensor status
Deposits on the BA electrode system can contribute to unstable readings. The gauge’s degas function heats the electron-collector grid to clean the electrode system in situ. Degas should be performed below 7.2 × 10-6 mbar. It stops automatically after a maximum of three minutes, and a new cycle cannot be started for 30 minutes. During degas, measurement values remain available, but their tolerances may be higher than during normal operation.
Pressure signals and status information are available through the gauge’s analog or supported digital interfaces, depending on model. This allows a control system to account for sensor errors and operating states rather than treating every output as a valid pressure reading. For fieldbus models, consult the instructions for the specific interface when configuring status and switching functions.
Practical implications for system designers
The BCG450’s three-sensor arrangement offers a single measurement channel across a broad pressure range, but effective use depends on matching the gauge version to the application. Engineers should check the process gas, expected pressure profile, controller interface, grounding, cable and power requirements, and potential contamination. They should also account for sensor handoffs and the different gas dependence of the measurement regions.
For plant teams, the practical benefit is a continuous pressure measurement approach spanning process and vacuum conditions, with options for analog, serial or fieldbus integration. Careful model selection, safe installation and attention to sensor status and maintenance conditions are essential to making that measurement useful in the wider automation system.