Access Official Technical PDF

Share Summary:LinkedInEmail

Choosing an industrial Ethernet processor involves more than comparing CPU speed. Automation equipment may need to handle application logic, field communication, timing, data movement and interfaces to sensors or other devices. The Renesas RZ/N1 family addresses these demands with three SoC groups—RZ/N1D, RZ/N1S and RZ/N1L—whose processing resources and networking options vary by device and package.

Understanding those differences is important when evaluating the family for controllers, communication equipment or other industrial embedded systems. The RZ/N1 combines Arm processing cores, on-chip memory, Ethernet functions and a broad peripheral set, but not every feature is available on every part or simultaneously.

How the RZ/N1 industrial Ethernet processor family is structured

The RZ/N1D and RZ/N1S include an Arm Cortex-A7 processor subsystem, while the RZ/N1L is based on an Arm Cortex-M3. The Cortex-A7 can operate at up to 500 MHz; the D group offers dual- or single-core configurations, and the S group uses a single Cortex-A7. The Cortex-M3, included across the family, operates at up to 125 MHz and has a memory protection unit.

This gives designers different starting points for application requirements. The A7-based variants provide a higher-performance application-processing option, while the M3-only RZ/N1L offers a distinct configuration for designs that do not require the Cortex-A7 subsystem. The datasheet lists floating-point support, memory management, caches and frequency scaling for the Cortex-A7 subsystem, along with clock-gating and frequency-scaling power features.

Memory resources also differ. The family includes extended on-chip SRAM with error correction, with configurations described as 2 MB and 4 MB. RZ/N1D devices can also include a DDR2/DDR3 controller; that interface is not listed for RZ/N1L. External storage options across relevant variants include NAND flash, Quad SPI, and SD/SDIO/eMMC, subject to device-level availability.

Industrial networking and protocol options

Networking is a central part of the RZ/N1 design. Its R-IN Engine combines a Cortex-M3-based networking subsystem with a hardware RTOS accelerator, hardware Ethernet acceleration and a dedicated Gigabit Ethernet MAC. The device family also offers an Advanced 5-Port Switch, independent Gigabit MAC instances on selected variants, and protocol-specific controllers.

Depending on the device and configuration, the networking capabilities include an EtherCAT slave controller with up to three ports, a Sercos III slave controller, and support for industrial Ethernet technologies identified in the family overview, including PROFINET, Ethernet Powerlink and EtherNet/IP. The Advanced 5-Port Switch supports quality-of-service queues, VLAN handling and IEEE 1588-2008 functionality. Separate redundancy-related options include PRP and HSR, while the switch also includes a DLR module.

These capabilities do not mean that every protocol controller or redundancy feature can be used together. The function comparison specifies restrictions: Sercos III, EtherCAT and HSR are not available simultaneously, and some smaller-package RZ/N1S and RZ/N1L configurations also have restrictions involving the Advanced 5-Port Switch. Hardware selection should therefore start with the required network protocol and topology, followed by verification of the exact part number and package.

Redundancy and timing considerations

For designs requiring network redundancy, the listed PRP and HSR functions are relevant, but availability is device-dependent and may be optional. The HSR switch supports functions such as redundant frame generation and duplicate-frame filtering. The Advanced 5-Port Switch supports IEEE 1588-2008 features, and independent GMACs also include IEEE 1588 support. These timing and redundancy functions can inform architecture decisions, but designers should confirm the applicable interface mode and feature combinations for their selected device.

Peripherals for control and system integration

Beyond Ethernet, the RZ/N1 family provides interfaces that can connect the processor to control, storage and communications subsystems. The peripheral set includes up to eight UARTs, two CAN interfaces, SPI master and slave channels, two I2C interfaces, USB 2.0, timers, GPIO and DMA controllers. Some UARTs support RS-485 and MODBUS-related features. The devices also include a parallel bus interface, with capabilities and operating modes varying by package.

Up to two 12-bit ADC units are available on selected variants, with sampling rates up to 1 MSPS. An LCD controller is included on RZ/N1D and RZ/N1S configurations, but not listed for RZ/N1L. These interfaces may help consolidate functions in an embedded design, although pin multiplexing and package-specific availability need to be checked during board planning.

DMA support can move data between memory and peripherals without relying exclusively on CPU-driven transfers. The family lists two DMA controllers, each with eight channels. On-chip SRAM includes single-error correction and double-error detection, while the NAND controller provides BCH error correction and bad-block management. These memory features are useful design considerations for systems that need to manage data integrity and external storage.

What to verify before selecting a device

The RZ/N1 product range spans different processor configurations, memory options, Ethernet port counts and package sizes. A feature present in the family overview may not be present in every SKU. For an initial evaluation, check:

  • Processing needs: Determine whether the design calls for a single or dual Cortex-A7, or the Cortex-M3-only RZ/N1L.
  • Network architecture: Confirm required protocol controllers, port count, redundancy mode and any restrictions on simultaneous functions.
  • Memory and storage: Match on-chip SRAM, external DDR support and flash or card interfaces to the system design.
  • Package and pin availability: Check the exact part’s package, pin multiplexing and peripheral access rather than relying on family-wide maximums.
  • Integration requirements: Review needed ADC, display, USB, serial, CAN and parallel-bus functions against the selected variant.

Conclusion

The Renesas RZ/N1 family brings processing, memory, industrial Ethernet functions and general-purpose interfaces together in a range of embedded SoCs. Its main value for system architects is the choice of configurations—from Cortex-A7-based devices to a Cortex-M3-only option—alongside integrated switching and protocol-specific networking features. Practical selection depends on matching the exact part and package to the application, especially where industrial protocols, redundancy, port count and feature coexistence are decisive.

Access Official Technical PDF

About The Author