Access Official Technical PDF

Share Summary:LinkedInEmail

FPGA partial reconfiguration allows a design to replace selected logic at run time without reconfiguring the entire device. For industrial automation and other systems with changing computational demands, this creates an opportunity to reuse programmable logic: hardware for one operating phase can be exchanged for hardware needed in another. A ViSARD soft-core processor extension demonstrates the approach by making floating-point execution units in the processor’s arithmetic logic unit (ALU) replaceable.

The implementation was designed around four priorities: high configuration speed, low latency, limited resource overhead, and preservation of hard real-time capability. Tests on a Zynq-7000-based platform showed that the controller reached the target FPGA’s specified maximum bitstream throughput. In a test design with three configurations, each containing between one and three execution units, the reconfigurable design also used roughly 40% fewer lookup tables (LUTs) than the corresponding non-reconfigurable design.

How FPGA partial reconfiguration enables hardware reuse

A conventional FPGA design keeps all required logic in place. If an application needs multiplication during one phase and sine calculations during another, a static implementation must include both sets of execution units even when only one is useful at a given time. Those units continue to occupy programmable logic resources.

With dynamic partial reconfiguration (DPR), a region of the FPGA can be assigned as a reconfigurable partition (RP). A reconfigurable module (RM) is loaded into that region as needed, while logic outside it remains in place. In the ViSARD design, the RP is associated with the processor’s ALU and holds exchangeable floating-point execution units. The active configuration can therefore provide the operations required for a particular stage of a program without permanently instantiating every unit.

This approach is most relevant when an application can be organized into phases with different operation requirements. Reconfiguration does not eliminate the need for the functions themselves; it changes when and where their hardware is present. The practical value depends on whether the area saved by sharing logic outweighs the resources and time needed to manage reconfiguration.

Integrating a reconfiguration controller

The system uses a custom partial reconfiguration controller (PRC) to transfer partial bitstreams from external RAM to the FPGA’s configuration interface. The transfer path uses a standard AXI bus, providing a defined method for communication between the controller and the memory that stores the bitstreams. A custom controller was selected to address the project’s goals for throughput and resource overhead.

Bitstream storage and delivery are important parts of the system design. The processor’s logic must request the appropriate configuration, and the PRC must move that configuration data to the target region. This makes reconfiguration more than a device-level operation: it requires coordination between the processor, memory, bus, controller, and FPGA fabric.

For real-time applications, this coordination needs particular care. Reconfiguration introduces work that does not exist in a static design, and the time taken to switch modules can affect when subsequent operations are available. The project set hard real-time capability as a design requirement, alongside low latency. The reported throughput result demonstrates that the controller reached the target device’s specified bitstream rate; it should not be interpreted as a universal guarantee of task deadlines. Those depend on the application’s schedule and the complete system’s behavior.

What the implementation results indicate

The test system switched among three configurations containing different combinations of execution units, with between one and three units in each configuration. The results indicate that partial reconfiguration can reduce FPGA resource use when the application’s operating phases need different hardware functions. In this test, LUT use fell by roughly 40% compared with the non-reconfigurable design.

That figure is specific to the tested design and configurations, rather than a general expectation for FPGA projects. The amount of savings depends on which modules are exchanged, how much logic remains common to all configurations, and the resources required to support reconfiguration. A design with little variation in its hardware needs may have less opportunity to benefit.

Partition design also matters. The exchangeable modules must fit within the assigned region and connect appropriately to the static logic around it. The processor integration therefore involves decisions about which execution units belong in the reconfigurable region, how their interfaces are organized, and how configurations are generated and stored. These choices affect both resource use and the practical complexity of the design.

Engineering considerations for automation systems

For system integrators and design teams evaluating DPR, the ViSARD implementation highlights several questions to resolve early:

  • Are workloads naturally phase-based? Sharing hardware is most useful when different phases require distinct sets of operations.
  • Can the switching time fit the schedule? Account for configuration transfer as part of the system’s timing behavior.
  • What is the net resource benefit? Compare the logic saved by exchanging modules with the resources used by the controller and supporting interfaces.
  • Can the modules share a stable interface? The reconfigurable region must integrate cleanly with logic that remains active.
  • How will configurations be managed? Bitstream generation, storage, selection, and delivery are all part of the implementation.

These checks help distinguish a genuine opportunity for resource sharing from a design in which a static implementation is simpler and better suited to the workload.

Conclusion

FPGA partial reconfiguration can make a soft-core processor’s hardware more adaptable by replacing selected execution units at run time rather than keeping every unit active in the design. The ViSARD extension demonstrates a custom AXI-connected controller and an ALU structure that supports exchangeable floating-point units. In the reported test, this approach reached the target FPGA’s specified bitstream throughput and reduced LUT use by roughly 40%. For industrial automation engineers, the practical lesson is to evaluate the complete tradeoff: potential resource savings must be considered alongside switching time, controller overhead, interface design, and the timing requirements of the application.

Access Official Technical PDF

About The Author