Access Official Technical PDF

Share Summary:LinkedInEmail

The SSI2164 quad VCA is a four-channel analog building block for audio designs that need voltage-controlled gain, filtering, mixing, or related signal-processing functions. Each channel has a current input, current output, and separate voltage-control port. For designers, the central choices are how to bias the gain cells, how to translate control voltages into the required gain range, and how to manage signal current, noise, and output-stage headroom.

The device provides a gain range from +20 dB to -100 dB, controlled by a ground-referenced voltage with a nominal constant of -33 mV per decibel. It can directly replace devices in existing SSM/V2164 positions while adding higher input-current handling and on-chip protection against asymmetrical power failure. These characteristics make it useful both as a replacement component and as a flexible core for new audio circuits.

How the SSI2164 quad VCA handles signals

Unlike a conventional voltage-in, voltage-out amplifier, each SSI2164 channel operates as a current-in, current-out gain cell. An input resistor converts an incoming voltage into current. The VCA steers that signal current according to the control voltage, and an external amplifier—typically an op amp—holds the output pin near virtual ground and converts current back into a voltage.

At a control voltage of 0 V, the channel has unity gain. A negative control voltage increases gain, while a positive voltage attenuates the signal. To cover the full specified range, the control voltage spans approximately -660 mV for +20 dB gain to 3.3 V for -100 dB attenuation. The control port has a nominal 10 kΩ input impedance, so series resistance can affect the applied voltage. Buffering is advisable where accurate gain settings are important.

The external circuit matters as much as the gain cell. The data sheet recommends an input resistor of 20 kΩ for many applications, with a usable range of 7.5 kΩ to 100 kΩ. Lower values can improve noise performance but increase distortion and make input-current headroom more relevant. A series resistor and capacitor at the input help ensure stable operation; the cited 220 Ω and 1200 pF network is a proven starting point.

Choosing Class A or Class AB operation

A single mode pin sets the operating behavior of all four channels. Leaving it open selects Class AB, which favors lower noise. Connecting a resistor from the mode pin to the positive supply injects mode current and moves operation toward Class A, which favors lower distortion. A resistor can also set an intermediate bias point.

This is a system-level trade-off rather than a simple performance upgrade. Increasing Class A mode current can reduce distortion, but raises noise and supply current. The data sheet identifies 1 mA as a useful general-purpose Class A setting, while cautioning that mode current must not exceed 2 mA. Designers should select the bias based on the signal level and the relative importance of distortion, noise, and power consumption.

  • Class AB: Leave the mode pin open for the best noise performance.
  • Class A: Use an external resistor to set mode current when lower distortion is the priority.
  • Intermediate bias: Adjust mode current to balance noise and distortion for the intended signal conditions.

Published typical figures include 0.025% distortion in Class A and a 118 dB dynamic range in Class AB. These are operating-mode-specific specifications, not guarantees for every circuit. The complete signal chain—including resistor selection, op-amp behavior, supply rails, and signal level—determines realized performance.

Designing the control and output stages

The VCA’s exponential control response suits traditional audio gain control. In applications where a control source provides a different voltage range or requires linear gain behavior, external circuitry can scale, invert, or linearize the control signal. The data sheet describes circuits for 0–5 V modular-synthesizer controls, including both linear and exponential approaches. The linear method uses a VCA in a feedback loop to correct for the companion channel’s exponential response.

At the output, an external op amp maintains virtual ground and provides voltage output. A feedback capacitor may be needed to preserve op-amp phase margin; 100 pF is identified as a value that works in many cases, though larger values trade bandwidth for reduced high-frequency noise. Output headroom can be limited by the op amp, so the output stage should be considered alongside the SSI2164’s supply voltage and intended signal range.

The device supports supplies from ±4 V to ±18 V. That range permits lower-voltage designs as well as systems seeking greater headroom, but supply selection does not remove the need for local bypassing and careful grounding. The data sheet recommends local 100 nF decoupling capacitors. It also notes that internal protection generally removes the need for the Schottky-diode solution used with earlier devices, while hot-plugged modular systems may warrant an additional diode measure.

Using four channels for more than gain control

The independent channels support several configurations beyond individual audio-level control. In a four-input mixer, each channel processes an input and the output currents are summed at a single op amp. Multiple outputs can be connected together for larger mixing requirements, with resistor values selected to suit the expected signal levels.

Channels can also be placed in parallel to reduce noise. In the documented approach, the inputs, outputs, and control ports are connected in common, with shared input and output networks. Component values must be adjusted for the number of channels: input and output resistances and the input RC resistor are divided by the number of parallel channels, while the associated capacitor is multiplied by that number.

Other documented uses include voltage-controlled filters, exponential generators, antilog converters, and a low-frequency oscillator. In a three-pole state-variable filter, three gain cells implement integrators and the fourth controls resonance. The SSI2164’s exponential response can also provide cutoff-frequency control in musical applications without a separate exponential converter.

Practical implications for circuit design

The SSI2164 is most effective when its current-mode architecture and shared mode control are treated as deliberate design constraints. Choose Class A or AB based on the required noise and distortion balance; check peak input current, especially with low input resistance and higher supplies; buffer control voltages when gain accuracy matters; and verify that the output op amp can meet the application’s stability and headroom needs.

For engineers developing or maintaining analog audio signal paths, the four-channel format offers room to combine gain control with mixing, filtering, or other circuit functions. Careful attention to bias, control scaling, resistor values, grounding, and decoupling helps translate the device’s broad capabilities into predictable circuit behavior.

Access Official Technical PDF

About The Author