The HV809 EL lamp driver is an offline, high-voltage integrated circuit for powering electroluminescent (EL) lamps. Its role is to convert a DC input into an alternating square-wave output across the lamp, making it relevant to engineers designing illuminated displays, portable instrumentation, and other equipment that uses EL lighting. Understanding its voltage limits, capacitive-load requirements, frequency control, and enable behavior is essential before integrating the device into a system.
How the HV809 EL lamp driver works
The HV809 accepts a high-voltage DC supply from 50V to 200V under its recommended operating conditions. The input may come from a rectified nominal 120V AC source or another suitable DC source. Internally, the device combines two oscillators, a low-voltage linear regulator, and a high-voltage output H-bridge.
The lamp connects between the VA and VB output pins. The H-bridge switches these outputs to produce an AC square wave across the lamp. The differential output voltage is twice the input DC voltage in peak-to-peak terms; at a 200V input, the stated minimum differential output is 400V peak-to-peak. This is the voltage across the lamp, not a separate supply rail.
The recommended maximum load capacitance is 350 nF, although the permitted load depends on operating conditions. For example, the electrical characteristics specify up to 350 nF with a 1 MΩ REL resistor at 170V HVIN, and up to 150 nF with a 390 kΩ resistor at the same input voltage. Engineers should assess the actual lamp capacitance alongside the selected frequency and supply conditions, rather than treating the maximum capacitance as valid for every configuration.
Setting lamp frequency and pulsing
An external resistor, REL, connects between the REL-Osc pin and ground to set the H-bridge output frequency. The data sheet gives two reference operating points: a 1 MΩ resistor corresponds to a typical 400 Hz output with a 350 nF load, while 390 kΩ corresponds to a typical 1 kHz output with a 150 nF load. These are specified conditions, not interchangeable settings; frequency, load capacitance, and supply voltage need to be considered together.
The HV809 also supports on/off pulsing of the lamp. On the eight-lead package, an external RC network can be connected between Osc1 and Osc2 to establish this behavior. Osc1 also controls whether the output H-bridge is enabled:
- Osc1 connected to ground: the output is enabled.
- Osc1 connected to VDD: the output is disabled.
This arrangement can support a pulsing function or a push-button delayed turn-off circuit, as illustrated in the device documentation. The specific RC values and circuit behavior should be selected using the applicable application guidance; the pin description alone does not define timing values.
Supply and load design considerations
Although HVIN is the high-voltage input, VDD is the device’s internal supply-voltage pin. Its specified range is 8V to 12V, with a typical value of 10V under the stated no-load condition. Application diagrams show a DC-DC converter supplying this low-voltage rail from a battery source, as well as input and VDD capacitors. The high-voltage input and internal supply therefore have distinct functions and should not be confused when laying out or reviewing the circuit.
The high-voltage supply current varies with load. At 170V HVIN, 1 MΩ REL, and a 350 nF load, the specified maximum is 70 mA. With a 50 nF load under the listed conditions, the maximum is 9 mA. The no-load quiescent current is specified separately and depends on the Osc1 state. These figures highlight why supply sizing should reflect the intended lamp load and operating mode rather than rely on a single current value.
The output rise and fall times are also load-dependent. At 150 nF and 170V HVIN, the typical rise time is 180 μs and the typical fall time is 50 μs; the listed maximums are 250 μs and 100 μs, respectively. These values can inform timing expectations where the lamp waveform matters to system behavior.
Package, thermal, and operating limits
The HV809 is available in an eight-lead narrow-body SOIC and an eight-lead SOIC with a heat slug. The heat slug is at ground potential. The listed power dissipation limits are 500 mW for the standard SOIC and 1.5 W for the heat-slug version. Their specified junction-to-ambient thermal resistances are 101°C/W and 84°C/W, respectively. Package selection and thermal design should account for the actual operating environment and dissipation.
Recommended ambient operating temperature is −25°C to +85°C. The absolute maximum HVIN rating is +210V, but this is a stress limit—not a recommended operating point. The recommended high-voltage input range ends at 200V. Staying within recommended conditions, and distinguishing operating ratings from absolute maximum ratings, is important for reliable circuit design.
Practical integration checklist
- Confirm that the DC input remains within the recommended 50V to 200V range.
- Determine the EL lamp capacitance and check it against the REL and input-voltage conditions.
- Select REL for the intended output frequency, then verify that the chosen load is supported at that operating point.
- Plan Osc1 control and any Osc1-to-Osc2 RC network for enable, pulsing, or delayed turn-off behavior.
- Check VDD supply requirements, load-dependent input current, package dissipation, and ambient temperature.
- Consult application note AN-H36 for detailed circuit and application information.
Conclusion
The HV809 provides a defined way to drive capacitive EL lamps from a high-voltage DC source, with output frequency set by an external resistor and optional control of lamp pulsing. For system designers, the key practical task is to treat supply voltage, lamp capacitance, frequency, and thermal conditions as connected design variables. Matching those conditions to the device specifications—and using the application guidance for circuit details—helps establish whether the HV809 is appropriate for a particular EL lighting function.