Access Official Technical PDF

Share Summary:LinkedInEmail

In semiconductor gas distribution, operators need to monitor pressure while also receiving a clear signal when a defined threshold is reached. A UHP pressure switch can meet both needs in one instrument: it displays pressure on a dial and uses a setpoint-operated switch to support alarms or control-system inputs. The IPS-300 is designed for high-purity, toxic, and corrosive gases used in semiconductor manufacturing and gas distribution systems.

How a UHP pressure switch combines indication and switching

The IPS-300 is a 2-inch indicating pressure switch. Its pointer provides a local reading, while an adjustable index marks the selected setpoint on the same dial. This lets personnel compare the current pressure with the threshold at a glance, without consulting a separate indicator.

A small magnet attached to the pointer actuates a magnetic switch as pressure moves the pointer through the setpoint. A magnetic latch allows the switch to remain in its on or off state after the pointer passes the operating point, without restraining pointer movement. The setpoint is adjusted at the front of the instrument by moving the index; access is provided by removing the window.

The switch action is selected as either closing on increasing pressure (HA) or closing on decreasing pressure (LA). That choice determines how the switching event relates to a rising or falling process pressure, so it should match the intended alarm or logic response. The selected action is identified on the pointer tail.

Connecting pressure status to alarms and PLC inputs

The switch is intended for low-voltage annunciators, indicator lights, and relays. It can also provide an input to a logic network, microprocessor, or programmable logic controller (PLC). With suitable pull-up or pull-down resistors, the monitor can connect to a microprocessor input. Unlike an analog pressure transducer, this arrangement provides a discrete switching event rather than a continuous electrical representation of pressure.

That distinction matters when specifying an instrument. A pressure switch is useful when the requirement is local pressure indication plus a defined threshold signal. If an application needs a continuously varying pressure value at the controller, the source describes the IPS-300 as a lower-cost alternative to an analog transducer with analog-to-digital conversion for digital input, but it does not replace the different measurement function of continuous-output sensing.

Electrical limits should be checked against the receiving device and load. The specified maximum is 10 W DC or 12 VA AC, with a maximum switching current of 0.5 A AC/DC for noninductive loads and a maximum switch voltage of 28 V AC/DC. The manufacturer advises consulting the factory for inductive loads such as relays. The switch itself requires no input power.

Pressure ranges, accuracy, and process connections

Available gauge ranges extend from 0–60 psi through 0–4000 psi, with intermediate ranges of 100, 200, 300, 600, 1000, 2000, and 3000 psi. Compound ranges are also offered, from vacuum to 30, 60, 100, 200, or 300 psi; the stated vacuum reference is 30 inches of mercury. Dual scales may be available by consultation with the factory.

Indication accuracy is specified as ±2% of span. The switch point operates within ±2% of full-scale span, which is a separate specification from the dial’s indication accuracy. The setpoint index is adjustable from 5% to 80% of span. When selecting a range, engineers should consider the operating pressure and the desired threshold together, ensuring the setpoint falls within the adjustment window.

Process connections are available as 1/4-inch NPT or Type 316L stainless-steel face-seal connections, including VCR configurations. Mounting options are low mount and center-back mount. For VCR face-seal connections, the specified surface finish is Ra 10 µinch (0.25 µm); the 1/4-inch NPT connections are specified at 32 Ra. Connectors ship with protective plastic caps.

Materials and cleanliness for high-purity service

The wetted internal surfaces, Bourdon tube, and process connection are Type 316L stainless steel. The case is electropolished Type 304 stainless steel and includes pressure relief. The product is cleaned and packaged for ultra-high-purity gas applications, and the specifications state that it exceeds ANSI B40.100. VCR face-seal versions are helium leak tested to 10−9 scc/sec.

These details help define suitability for the intended gas system, but they do not eliminate the need to confirm compatibility with the process gas, connection standard, installation practice, and applicable facility requirements. Ambient operating temperature is specified from −4°F (−20°C) to 149°F (65°C), while maximum fluid temperature is 212°F (100°C).

Practical selection considerations

  • Choose the pressure range: Match the gauge or compound range to the operating conditions and required setpoint.
  • Specify switch action: Select HA for closing on rising pressure or LA for closing on falling pressure, based on the intended logic.
  • Check the interface: Verify voltage, current, power, and load type against the alarm, relay, or controller input.
  • Confirm installation details: Select low or center-back mounting and the required NPT or face-seal connection.
  • Review the switching tolerance: Account for the ±2% of full-scale switch-point accuracy when setting alarm expectations.

Conclusion

A UHP pressure switch provides a straightforward way to combine a visible pressure reading with a discrete setpoint signal in semiconductor gas systems. The IPS-300’s adjustable dial index, magnetic switching mechanism, range choices, and connection options support different monitoring and installation needs. Careful review of pressure range, setpoint tolerance, switch direction, electrical limits, materials, and mounting helps ensure the instrument fits the process and control-system requirement.

Access Official Technical PDF

About The Author