Access Official Technical PDF

Share Summary:LinkedInEmail

The GPON physical layer determines how optical signals travel between a provider-side termination and user-side network units across a passive fibre access network. For engineers and technical decision-makers evaluating fibre infrastructure, understanding this layer helps clarify what equipment and optical paths must support—and where other parts of the system take over. ITU-T Recommendation G.984.2 specifies the physical media dependent (PMD) layer for gigabit-capable passive optical networks, including supported line rates, optical interfaces and provisions for monitoring link conditions.

What ITU-T G.984.2 defines

G.984.2 sets physical-layer requirements for an optical access network that can transport services between a user-network interface and a service node interface. Its focus is the fibre transmission environment and the optical interfaces at either end of the distribution network. The recommendation covers both symmetrical and asymmetrical GPON configurations, with different nominal rates available in the downstream and upstream directions.

The PMD layer is one part of the system rather than the complete GPON specification. It addresses the physical characteristics of transmission. The transmission convergence (TC) layer and ranging protocol are specified separately in ITU-T G.984.3. This distinction matters in system design: optical performance and fibre-path requirements belong to the PMD considerations, while functions assigned to the TC layer are covered by the companion recommendation.

GPON physical layer rates and directions

Downstream communication runs from the optical line termination (OLT) toward one or more optical network units (ONUs). Upstream communication travels from the ONUs back to the OLT. G.984.2 specifies downstream nominal rates of 1,244.16 or 2,488.32 Mbit/s. Upstream options are 155.52, 622.08, 1,244.16 or 2,488.32 Mbit/s. This range allows systems to use symmetrical or asymmetrical downstream and upstream rates.

In the upstream direction, an ONU transmits when it is in an operating state and has been given a transmission grant; it must not transmit without one. That controlled transmission is relevant to the optical interface because upstream traffic is burst-mode and the ONU transmitter’s behaviour between assigned slots is specified. The PMD requirements address characteristics such as launched optical power and transmitter timing around assigned transmissions.

Fibre topology, wavelengths and transmission

The optical distribution network (ODN) uses a point-to-multipoint tree-and-branch arrangement. It comprises optical fibre supplemented by passive components such as power or wavelength splitters and filters. A common OLT endpoint connects through the ODN to distributed ONU endpoints. An ONT is a specific type of ONU designed for a single subscriber; the term ONU can also refer to a device serving multiple subscribers.

Bidirectional transmission can use wavelength division multiplexing on one fibre or separate fibres for the two directions. For single-fibre systems, the specified downstream wavelength range is 1,480–1,500 nm; upstream operates at 1,260–1,360 nm. In two-fibre systems, downstream uses 1,260–1,360 nm, while upstream remains in that range on its separate fibre. The recommendation bases its fibre requirements on the characteristics specified in ITU-T G.652.

Both directions use non-return-to-zero (NRZ) line coding at the PMD layer. G.984.2 specifies the optical interface behaviour, while the scrambling method is not defined at this layer. Keeping these details distinct helps integrators assess interface compatibility without treating the PMD specification as a complete description of every GPON protocol function.

Link budgets and optical path planning

Optical path loss is a central design constraint. G.984.2 identifies ODN attenuation classes A, B and C, with specified attenuation ranges of 5–20 dB, 10–25 dB and 15–30 dB respectively. The appropriate class and supported split ratio are constrained by the path loss. The recommendation also specifies parameters for transmitters and receivers, including launched power, receiver sensitivity, overload and tolerance to reflected optical power.

These are system-level design values, not a substitute for checking the actual optical path. Fibre distance, splitters, connectors and other passive components all contribute to the path that the optical interfaces must support. The recommendation lists a maximum fibre distance between send/receive and receive/send reference points of 20 km, with 10 km as an option, and a maximum logical reach of 60 km. Logical reach is managed by higher-layer system functions and should not be confused with the physical fibre-distance figure.

G.984.2 also defines differential optical path loss and differential logical reach. These address different aspects of a multi-ONU system: the former concerns variation in optical path loss, while the latter concerns differences in logical reach among ONUs. Both can be relevant when assessing whether a proposed distribution layout fits the system parameters.

Optical supervision and engineering checks

The recommendation includes parameters to support optical layer supervision (OLS), described as capabilities for measuring and reporting the state of an optical link. Its provisions cover transceiver-parameter monitoring and physical-layer performance measurements. For operations teams, such measurements can provide a defined basis for observing optical conditions, alongside the network’s management and maintenance functions.

When reviewing a GPON design or specification, technical teams should distinguish among:

  • Line rate: confirm the selected downstream and upstream rates are supported by the equipment.
  • Optical path: compare the expected attenuation and split arrangement with the applicable ODN class.
  • Interface compatibility: check wavelength direction, fibre arrangement and transmitter/receiver requirements.
  • Layer responsibilities: consult G.984.3 for TC-layer and ranging details rather than assuming these are defined by the PMD specification.
  • Supervision needs: identify which optical parameters are measured and how their results fit into network operations.

Practical implications for network planning

ITU-T G.984.2 provides a common physical-layer framework for GPON equipment and optical access network design. Its value is not just the list of available bit rates: it also connects those rates to wavelength use, fibre topology, optical budgets and interface behaviour. For engineers, integrators and operations leaders, applying the specification means checking the complete optical path and confirming that each component and endpoint is appropriate for the selected system configuration.

The practical takeaway is to treat the GPON physical layer as a coordinated set of constraints. Rate selection, ODN loss, fibre arrangement and optical interface characteristics must be considered together, while TC and ranging functions should be checked against their separate specification. This disciplined division supports clearer equipment selection, more consistent design reviews and better-defined optical supervision requirements.

Access Official Technical PDF

About The Author