A bidirectional onboard EV charger is more than a way to replenish a vehicle battery: it can also return stored energy to the electrical grid or transfer it to another vehicle. As electric and plug-in hybrid vehicles evolve, charger design must balance power, efficiency, size, weight, and isolation. Understanding the available charging approaches—and the role of power electronics in each—helps engineers and decision-makers assess which solutions fit a particular use case.
EV charging systems: four approaches
Charging systems for electric and plug-in hybrid vehicles generally fall into four categories: wired onboard charging, wired external charging, wireless inductive charging, and battery swapping. Each involves different infrastructure and vehicle requirements.
Onboard and external wired charging
An onboard charger is installed in the vehicle and converts power supplied through a charging connection into a form suitable for the battery. External, or offboard, chargers contain the conversion equipment outside the vehicle and can provide higher charging power. The reviewed charging levels include slower charging from a residential supply, higher-power AC charging for workplaces and shared parking, and fast charging using DC equipment.
The trade-off is practical as well as electrical. An onboard charger travels with the vehicle, so its power electronics must fit within limits on vehicle mass and volume. External fast chargers can support higher power, but require dedicated charging equipment and infrastructure. Charging time also depends on the battery and charging conditions; the paper notes that rapid charging commonly refers to reaching around 80% capacity, with charging the remainder taking longer as charging current is reduced.
Chargers can also be classified by power-flow direction. A unidirectional unit charges the battery only. A bidirectional unit can additionally send energy from the battery to the grid, a capability often called vehicle-to-grid (V2G), or to another vehicle through vehicle-to-vehicle (V2V) transfer.
Wireless charging and battery swapping
Inductive Power Transfer (IPT) uses magnetically coupled coils: a primary unit outside the vehicle transfers energy to a secondary unit onboard. The absence of a physical cable and the inherent galvanic isolation are benefits. However, coil alignment and separation affect magnetic coupling and efficiency, while the vehicle-side receiver adds equipment. The paper also identifies standards and interoperability between systems as challenges.
Battery swapping takes a different approach: rather than charging the installed battery, a depleted pack is exchanged for a charged one. The paper describes rapid exchange as an advantage, while noting the need for purpose-built stations and space to accommodate them. It also discusses centrally managed batteries as a possible resource for grid support.
Designing a bidirectional onboard EV charger
The proposed charger is a concept, not a reported production system. Its target is a 5 kW isolated, bidirectional onboard charger supplied from a single-phase 230 V AC connection. The stated output voltage range is 250–450 V DC, with a 350 V DC intermediate link. The design also specifies a power-density target above 5 kW/dm3 and switching frequency above 300 kHz. These are design goals, not demonstrated results.
The architecture has two main conversion stages:
- AC/DC stage: A full-bridge converter is intended to operate as an active rectifier during charging and as an inverter when power flows back toward the grid.
- DC/DC stage: A high-frequency Dual Active Bridge (DAB) converter transfers energy between the DC link and battery. A high-frequency transformer provides galvanic isolation.
Isolation matters in the proposed arrangement because the battery’s negative terminal may be connected to the vehicle chassis. The transformer in the DAB stage separates the battery-side circuit from the upstream conversion stage while enabling bidirectional energy transfer.
Why use wide-bandgap switches and active decoupling?
The concept combines gallium nitride (GaN) transistors in the AC/DC and DC/DC stages with silicon carbide (SiC) transistors in an active power-decoupling circuit. The design rationale is that wide-bandgap devices can support higher switching frequencies while maintaining efficient power conversion. Higher switching frequency can, in turn, allow smaller passive components, including inductors. The paper’s comparison of selected devices estimates lower switching losses for the GaN example than for the silicon MOSFET example under its stated analysis conditions; this comparison supports the design rationale but does not establish the performance of the complete charger.
Active power decoupling addresses another size constraint. Power variation between the AC input and DC output can require energy storage in the intermediate circuit. In a conventional design, this can mean a substantial capacitor bank. The proposed active circuit is intended to reduce the required capacitance and enable the use of smaller film capacitors in place of electrolytic capacitors. The paper cites earlier work on this approach, but the proposed charger itself would still need to be built and tested to verify its overall performance.
Engineering implications
For design teams evaluating onboard charging, the architecture highlights several linked decisions: required charge power, the need for bidirectional operation, isolation strategy, semiconductor technology, and the volume available for passive components. Improvements in one area can introduce additional components or control requirements elsewhere. For example, active decoupling may reduce capacitor volume but adds circuitry that must be designed and validated.
The concept also makes clear that charger efficiency and compactness depend on the complete conversion system, not a single component. The paper identifies future work on modulation and control strategies to reduce switching losses and balance device loading. Those strategies are proposed development steps, rather than confirmed features or results of a completed charger.
Conclusion
EV charging encompasses distinct solutions, from vehicle-mounted AC conversion to external fast charging, inductive power transfer, and battery swapping. For onboard systems, a bidirectional AC/DC and isolated DC/DC architecture can support charging and energy return, while GaN and SiC devices and active power decoupling offer potential routes toward a more compact design. The practical takeaway is to treat power level, isolation, energy-flow direction, and component volume as connected design requirements—and to distinguish carefully between a proposed target and validated system performance.