Access Official Technical PDF

Share Summary:LinkedInEmail

High-temperature solar thermal systems need to capture sunlight efficiently without losing too much energy as infrared radiation. A spectrally selective solar absorber addresses this challenge by absorbing strongly across the solar spectrum while limiting thermal emittance at longer wavelengths. A free-standing silicon thin-film design demonstrates how material thickness and a straightforward layered structure can help balance optical performance, flexibility and manufacturability.

The composite was characterized at temperatures up to 595°C and tested through thermal cycles at 600°C. Its results are relevant to engineers and decision-makers assessing materials for solar heat collection and thermophotovoltaic (TPV) systems, where controlling the spectrum of absorbed or emitted energy affects system performance.

Why spectral selectivity matters at high temperatures

A solar absorber does not benefit from high solar absorption alone. As its temperature rises, it also radiates heat away. The useful thermal transfer therefore depends on both solar absorptance and thermal emittance, as well as the operating temperature and solar concentration. In general, an effective selective absorber should absorb strongly at solar wavelengths—approximately 0.3 to 2.0 micrometres—and emit less at longer wavelengths.

This balance becomes especially important at high temperatures and relatively low solar concentrations, where thermal radiation losses can undermine the value of captured energy. Solar thermal systems can store heat for later electricity generation, while TPV systems use a thermal emitter to direct radiation toward a photovoltaic diode. For TPV, emission should be concentrated in wavelengths the diode can convert; unwanted below-bandgap radiation can contribute to losses and diode heating.

A flexible, thin-film silicon absorber

The reported spectrally selective thin-film silicon absorber/emitter, or SSTFS, uses a three-layer arrangement: a silicon nitride antireflection coating, a thin silicon absorber and a silver back reflector. The layers are made from commercially available materials, and the design does not rely on a rigid substrate. That substrate-free construction allows the film to flex and conform to curved surfaces—an option that rigid absorber structures may not offer.

Fabrication begins with a commercial silicon wafer. Wet etching reduces the silicon to its target thickness; silver is then deposited on the back, followed by the silicon nitride coating on the front. A temporary edge handling ring supports the wafer during processing and can later be removed. The approach uses established deposition and etching methods, which the study presents as a basis for scalable fabrication rather than a demonstration of production-scale output.

Silicon thickness is central to the design trade-off. Thick silicon can absorb sunlight effectively, but its thermal emittance can rise as temperature increases, partly because of intrinsic carrier absorption. Reducing the silicon thickness helps suppress this mid-infrared emission. The study identifies an optimal thickness of around 10 micrometres for balancing absorption and emittance in this design. The resulting free-standing film was shown conforming around a 1.27-centimetre-diameter rod without breaking.

High-temperature performance and potential applications

Measurements at 505°C and 595°C showed strong spectral selectivity, with experimental emittance spectra matching simulations closely. At 595°C, the absorber had a reported solar-averaged absorptance of 0.76 and thermal-averaged emittance of 0.23. Under the study’s specified condition of 50 suns, the calculated thermal transfer efficiency was 0.61. These figures describe the tested material and modeled operating conditions; they should not be interpreted as a complete system-level efficiency for a solar installation.

The thin film also showed lower mid-infrared emittance than a thicker, wafer-based silicon design used for comparison. That reduction matters because less thermal radiation escapes from a solar absorber, while a selective emitter in a TPV system can limit unwanted sub-bandgap emission. For a modeled TPV case using a 1.1 eV photovoltaic bandgap, the study reported above-bandgap average emittance of 0.68 and below-bandgap average emittance of 0.23 at 595°C. Actual TPV performance also depends on the photovoltaic device and other system parameters, so these material results alone do not establish application-level output.

Thermal cycling highlights a durability trade-off

For practical deployment, optical performance must be considered alongside stability over time. The SSTFS sample was heated to 600°C under high vacuum for two cycles: one hour at the maximum temperature in the first cycle, followed by five hours in the second. Its overall spectral selectivity was maintained after six hours of total annealing, although a slight increase in emittance indicated some degradation.

After a longer test consisting of four six-hour cycles, the study observed more significant degradation and partial delamination. The reported evidence pointed to deterioration of the silver back reflector or the silicon-silver interface as the likely issue; the thin-film silicon itself was described as stable under separate high-temperature testing. This makes reflector and interface durability an important engineering consideration, not a resolved qualification question. The authors identify replacing silver with a refractory reflector as a possible direction for improving thermal stability.

What engineers should take from the design

The SSTFS illustrates a useful design principle: performance at elevated temperature can depend as much on controlling unwanted emission as on maximizing absorption. Its thin silicon layer reduces mid-infrared emittance, while its substrate-free structure adds mechanical flexibility. The three-layer construction also avoids the complex nanostructures that can create manufacturing and cost challenges.

  • For solar thermal systems: assess absorptance and thermal emittance together at the intended operating temperature and concentration.
  • For TPV systems: evaluate the emitter spectrum alongside photovoltaic bandgap, diode heating and other system-level factors.
  • For deployment planning: consider the reflector and layer interfaces as potential lifetime constraints, and distinguish short-duration thermal-cycle results from longer service requirements.

Overall, this flexible silicon composite offers a promising material approach for high-temperature solar absorbers and thermal emitters, with measured selectivity at temperatures up to 595°C and stability demonstrated over six hours at 600°C. Its practical value will depend on matching optical performance to system requirements and improving the durability of the reflective layer for longer operation.

Access Official Technical PDF

About The Author