Access Official Technical PDF

Share Summary:LinkedInEmail

Silicon solar cell thickness is not simply a matter of using more material to absorb more light. In rear-contact cells, base thickness interacts with photon transport and carrier recombination, so the thickness that maximizes efficiency depends on both optical and electrical behavior. A theoretical analysis of commercial back-contact silicon cells shows how these effects can be evaluated together, including the roles of front-surface recombination and recombination within the silicon.

For engineers and technical decision-makers assessing photovoltaic cell design, the practical takeaway is that thickness should be optimized for the cell’s surface properties and light-trapping behavior—not treated as an independent specification. The analysis also highlights why different rear-contact cell designs can have different optimal thicknesses even when their basic architecture is similar.

Why rear-contact cell design changes the analysis

In a back-contact silicon solar cell, the collector junction and both contact electrodes are located on the rear, non-illuminated surface. This arrangement differs from a conventional front-contact cell and makes recombination at the illuminated surface particularly relevant. When light enters the cell, it generates electron-hole pairs; those carriers must reach the junction and contacts before recombining.

The study models key electrical characteristics, including short-circuit current, open-circuit voltage, the current-voltage curve, fill factor and photoconversion efficiency. Its one-dimensional approach assumes that excess carrier concentration is nearly uniform through the silicon base. This simplification is considered applicable when the carrier diffusion length is much greater than the base thickness and the combined surface recombination is sufficiently low relative to the ambipolar diffusion coefficient and thickness.

Those conditions matter: the model is not a universal description of every cell geometry or operating condition. In particular, front-surface recombination can be significant in rear-contact cells, so it cannot always be treated as negligible.

Recombination losses that influence cell performance

Recombination reduces the number of photogenerated carriers available to contribute to current or voltage. The model accounts for several pathways in silicon, rather than representing all losses with a single fixed lifetime:

  • Shockley-Read-Hall recombination: carrier loss associated with recombination centers in the silicon.
  • Non-radiative exciton-assisted Auger recombination: a non-radiative process assisted by deep impurities.
  • Band-to-band Auger and radiative recombination: additional bulk processes that affect the effective recombination lifetime.
  • Surface recombination: carrier loss at the illuminated front and rear surfaces.
  • Space-charge-region recombination: recombination associated with the junction region.

Including space-charge-region recombination is important to the analysis. Although its effect might appear small when compared with bulk recombination under some assumptions, the effective lifetime in the junction region can be much shorter than in the neutral silicon base. Consequently, junction-region recombination may compete with other loss mechanisms, including under conditions near the cell’s maximum-power operating point.

How thickness affects current and efficiency

Increasing base thickness can improve the opportunity for incoming light to be absorbed. In textured silicon, the optical path through the material can be longer than the cell’s physical thickness, and the analysis represents this behavior through the external quantum efficiency—the fraction of incident photons at a given wavelength that produce collected carriers. The short-circuit current can be estimated from this spectral response together with the incident photon flux.

But a thicker base is not automatically more efficient. Surface recombination at the front can reduce the short-circuit current, and the size of this effect depends on the front-surface recombination velocity, base thickness and carrier transport properties. The model distinguishes this front-surface contribution from the combined recombination at the front and rear surfaces, which also affects the open-circuit voltage.

As a result, two competing effects shape the efficiency-versus-thickness curve:

  • Optical benefit: increased photon path length in textured silicon can support greater light absorption.
  • Electrical penalty: surface recombination, especially at the illuminated surface, can limit current and shift the thickness at which efficiency peaks.

The balance depends on cell characteristics. The analysis finds that higher total surface recombination is associated with a greater optimal base thickness. Increasing front-surface recombination, in contrast, reduces both the maximum efficiency and the optimal thickness.

What the modeled commercial cells show

The theoretical results were compared with experimental current-voltage and spectral-response data for commercial rear-contact cells. For one cell with a measured base thickness of 165 micrometers, the modeled efficiency peaked at a greater thickness, while the efficiency reduction at the measured thickness was relatively small. A separate cell with a reported efficiency of 24.3% was modeled with an optimal thickness of 173 micrometers. For a record-efficiency example reported at 25.2%, the modeled optimum was 141 micrometers.

These are results for the particular cells and assumptions analyzed, not universal design targets. They illustrate that the optimum can change with surface recombination and optical response. The modeled efficiency curves for the SunPower cells were also relatively flat across a range around 150 micrometers, indicating that small departures from the calculated optimum did not necessarily produce a substantial efficiency reduction in those cases.

Implications for cell evaluation and design

For photovoltaic engineering teams, the analysis underscores the value of treating thickness, optical response and recombination as connected design variables. A thickness comparison is more meaningful when it considers both the spectral quantum efficiency and the front and rear surface conditions. Dark and illuminated current-voltage data can also help constrain recombination and resistance parameters used in a model.

Model assumptions should remain visible when interpreting results. The analysis uses a one-dimensional carrier profile and specific recombination descriptions; its predictions depend on the parameter values used for each cell. The reported comparison between theory and measurements supports the approach for the cases examined, but does not remove the need to characterize the cell being evaluated.

Conclusion

Optimizing silicon solar cell thickness means balancing light absorption against carrier losses. In rear-contact cells, textured-silicon photon path length can favor a thicker base, while front-surface recombination can lower current and move the efficiency optimum toward a thinner design. Considering bulk, surface and space-charge-region recombination together provides a more complete basis for interpreting cell performance. The practical implication is clear: thickness decisions should be made in the context of measured or modeled optical response and recombination behavior, rather than from thickness alone.

Access Official Technical PDF

About The Author