Access Official Technical PDF

Share Summary:LinkedInEmail

Nonlinear electrical loads can draw distorted current from a supply, creating harmonics that affect power quality. In industrial facilities, these current components can contribute to voltage distortion, equipment malfunction and transformer overheating. An active power filter can address these issues by generating compensating current, while also supporting reactive power compensation. Choosing an appropriate configuration requires understanding how active and passive elements share the filtering work.

Why power quality is a concern

Power-electronic equipment and other nonlinear loads do not draw current in the same smooth waveform as a linear load. Their current contains harmonic components in addition to the fundamental-frequency component. As these currents flow through the electrical system, they can distort feeder voltage and affect sensitive equipment. Nonlinear loads can also increase reactive current and reduce input power factor.

These effects make power quality relevant to plant engineers and system integrators as well as utility operators. Filtering solutions are intended to reduce the harmonic current seen by the supply and, depending on their configuration and control, compensate reactive current. The objective is to improve the current drawn from the utility without changing the nonlinear load itself.

How a shunt active power filter works

A shunt active power filter is connected in parallel with the load. Its power converter uses control circuitry to determine the compensating current required and injects that current into the power lines. The compensation can include the load’s harmonic components and its fundamental reactive component. When the injected current is properly controlled, the utility supplies a more sinusoidal current that is closer in phase to the utility voltage.

The converter is connected to the AC system through inductors, which act as switching-ripple filters. A conventional three-phase arrangement uses a three-arm bridge converter. The filter’s power electronics must generate the required compensation current, so the converter rating is related to the load current that needs compensation. This can make a purely active solution costly or less suitable for larger-scale applications.

Active filters differ from passive filters in their ability to generate specific current components to address changing harmonic and reactive-current requirements. However, the power converter’s capacity and cost are important design considerations. These factors help explain why hybrid arrangements combine active and passive components.

Hybrid power filters: sharing the filtering task

A hybrid power filter combines a power converter with passive filtering elements. In the described configuration, a series inductor-capacitor set provides passive filtering, while the converter remains responsible for active compensation. Because the passive filter can handle part of the filtering function, the converter’s required capacity can be lower than in a purely active arrangement.

This approach aims to retain the benefits of active filtering while reducing some limitations associated with relying on a power converter alone. The passive network and converter must be considered as parts of one system: their roles, connections and control determine how the filter responds to harmonics and reactive power. A hybrid design is therefore not simply a conventional active filter with extra components; the passive elements are configured to contribute to the filtering operation.

How the proposed reduced-switch topology differs

The proposed three-phase arrangement uses a reduced-switch-count, transformerless circuit based on a two-arm bridge, along with filter inductors and capacitive and resistive filtering elements. It also uses a series inductor-capacitor set, but the stated function of this set differs from its role in the hybrid filter described above.

In this proposed arrangement, the series inductor filters switching ripple produced by the power converter, while the capacitor supplies fixed reactive compensation. The reduced number of power-electronic devices is a feature of the circuit topology. The design is intended to perform active filtering and provide enhanced reactive power compensation, with the paper describing its capability in terms of complete reactive compensation.

The analysis separates the fundamental compensating current into active and reactive components. The active component supports converter losses and DC-link voltage control; the reactive component is used to compensate the load’s fundamental reactive power. In steady operation, the active component is described as small, with the converter maintaining the DC-link voltage. This distinction is useful when assessing how a filter can both correct current distortion and support reactive-power requirements.

Practical considerations for selection

For an industrial application, filter selection starts with the characteristics of the load and the problem to be addressed. Engineers should consider the harmonic current to be compensated, the reactive-power requirement and the scale of the installation. The choice between a purely active filter and a hybrid topology involves trade-offs between converter capacity and the contribution of passive components.

  • Connection point: A shunt filter is installed in parallel with the nonlinear load and injects compensating current into the power lines.
  • Converter duty: The required power-converter capacity is tied to the current that must be compensated.
  • Passive components: Inductors and capacitors can provide ripple filtering, passive filtering or fixed reactive compensation, depending on the topology.
  • Control objectives: Harmonic compensation, reactive-power compensation and DC-link voltage maintenance are related but distinct functions.

These considerations also matter when integrating filters into grid-connected systems, including systems with renewable energy sources. The topology and control should be evaluated against the specific electrical conditions and compensation objectives rather than treated as interchangeable across installations.

Conclusion

Active power filters improve power quality by injecting current that counteracts harmonic and reactive components drawn by nonlinear loads. Shunt configurations provide parallel compensation, while hybrid filters use passive elements alongside a converter to share the filtering task. Reduced-switch designs pursue a more compact converter structure while assigning defined roles to inductors and capacitors. For plant teams, the practical decision is to match the filter topology and converter capacity to the load, harmonic-compensation needs and reactive-power requirements.

Access Official Technical PDF

About The Author