Access Official Technical PDF

Share Summary:LinkedInEmail

A successful Altivar 61 drive setup is more than entering a speed reference and pressing Run. Commissioning involves confirming electrical and motor compatibility, configuring command and reference paths, and understanding how parameter choices affect one another. A structured approach helps engineers and integrators reduce setup errors and gives plant teams a clearer basis for troubleshooting and future changes.

Start with safety and equipment checks

Before installing, adjusting or maintaining a drive system, work must be performed by qualified personnel familiar with the equipment and applicable safety requirements. The system integrator is responsible for grounding and compliance with relevant electrical codes and regulations. Drive components and terminals can carry hazardous voltage, so follow the product’s safety procedures rather than relying on display indications alone.

Before working on the system, disconnect all power sources, including external control power, and prevent reconnection using the site’s lockout procedure. The manual specifies waiting 15 minutes for the DC bus capacitors to discharge, then measuring the DC bus with a properly rated voltmeter to verify that voltage is below 42 Vdc. A DC bus LED does not establish that the bus is safe. Install and close covers before applying power, and do not operate equipment that appears damaged.

Before power-up, verify that the supply voltage is compatible with the drive nameplate. Also check that the Power Removal input and run-command inputs are in the required inactive state during configuration; an active command can cause unintended motor operation. Frequent line-contactor operation should be avoided, and the manual warns that cycle times below 60 seconds may damage the pre-charge resistor.

Plan the Altivar 61 drive setup sequence

The recommended workflow separates installation from programming. First complete mounting and wiring using the installation documentation. Then power up without a run command, select the language if using the graphic display terminal, and configure the Simply Start menu. The drive should be stopped and have no run command while configuration parameters are changed, except for functions such as auto-tuning that can cause the motor to start.

Simply Start is intended to provide a fast initial configuration for many applications. Enter its parameters in the order shown because later choices can depend on earlier ones. For example, select two-wire or three-wire control before configuring other startup parameters. If settings in other menus have already been changed, some startup values may be affected, so keep a record of the configuration and review the relevant settings before commissioning.

Choose a suitable macro configuration

The drive provides five macro configurations: Start/stop, General use, PID regulator, Communication bus, and Pumps/fans. A macro configuration assigns a group of parameters for a broad application type; it does not prevent further customization in other menus. Pumps/fans is the factory configuration. Changing the macro configuration reinitializes its input and output assignments, so review those assignments whenever selecting a different macro.

Factory settings may suit an application, but should not be treated as proof that the drive is ready to run. The standard configuration includes a 50 Hz motor frequency, linear acceleration and deceleration ramps of 3 seconds, and a maximum speed of 50 Hz. It also assigns logic and analog inputs, relays, and motor protection settings. Compare each applicable value with the actual motor, machine and control design.

Configure motor data and control behavior

Enter motor nameplate information in the motor-control settings, including rated voltage, current, power and frequency as applicable. The drive’s control method and protection behavior must match the application. The manual recommends auto-tuning to optimize performance; plan for this operation as part of commissioning and follow the drive’s instructions because auto-tuning can start the motor.

Special arrangements require specific attention. For motors connected in parallel, the manual calls for a V/F control type. It also warns that drive-based motor thermal protection may not be provided in certain configurations or when motor current is below 0.2 times the rated drive current. Provide an alternative means of thermal protection where required by the selected setup. If the motor’s nominal voltage is lower than the drive supply voltage, the specified vector-control setting must be used to limit motor voltage, and the applied voltage must be checked against motor characteristics.

Verify command, reference and I/O paths

A variable speed drive responds to configured command and reference channels. These can involve terminals, the graphic display terminal, integrated communications or a communication option. Confirm which channel controls start and stop and which provides the speed reference. Check that the physical wiring matches the configured inputs and that inactive inputs are not assigned in a way that could trigger unexpected behavior.

The drive’s menu structure helps organize this work:

  • Simply Start: Core startup parameters and macro configuration.
  • Motor Control: Motor nameplate data, auto-tuning and control settings.
  • Inputs/Outputs Configuration: Input and output assignments and related settings.
  • Command: Command and reference channel selection.
  • Application Functions: Functions such as preset speeds and PID regulation.
  • Fault Management and Diagnostics: Fault response settings and drive or motor status information.

Use the terminal and access levels effectively

The graphic display terminal presents menus, parameter names and values, while the integrated terminal uses a four-digit display. On the graphic terminal, the navigation control selects menus and values; the function keys can provide contextual actions. Changes are saved by confirming them with the navigation control, while Escape cancels an edit. The integrated terminal also requires confirmation to store a selection.

Access levels determine which menus and functions are available. Basic access limits configuration options, Standard is the factory level, and Advanced and Expert provide broader access, including additional parameters at Expert level. Access can also affect how many functions may be assigned to an input. Select an appropriate level for the work being performed, and use configuration records to make changes reviewable by the wider maintenance team.

Parameter values can be interdependent. For example, enabling a sinus filter can limit the available switching frequency or change its factory value. Reversing the filter setting does not necessarily restore the previous switching-frequency value. After changing a parameter that influences another setting, review the resulting values rather than assuming they have returned to their former state.

Commission methodically before handing over

Before starting the motor, verify wiring against the configured control scheme, confirm the motor and drive data, and check that run commands are inactive until the intended test. Validate the operating direction, reference source, ramp behavior and relevant fault response under controlled conditions. Record the final settings so that maintenance personnel can distinguish intentional configuration from factory defaults.

The practical lesson is straightforward: safe, repeatable Altivar 61 commissioning depends on a defined sequence, accurate motor information and careful verification of control paths and interdependent parameters. Treat the startup menu as a foundation, not a substitute for application-specific review. That discipline helps teams bring the drive into service with a configuration they can understand, maintain and troubleshoot.

Access Official Technical PDF

About The Author